“More information https://www.caravansplus.com.au"
PRODUCT CARE
DEFROSTING
2.
Empty
the
refrigerator.
3. Leave the cabinet and freezer doors
open. Filling
the ice
tray
with hot water and
placing
it on the
freezer shelf can reduce
defrosting
time.
Defrost water
Defrost water collects in the
drip tray
and is routed
to the outside
though
the drain tube which should be
installed
through
the floor.
4. When the ice has
melted,
dry
the interior of the
refrigerator
with a clean cloth.
5.
Ensure the
drip tray
is in it's
original position.
6.
Replace
all food and set the thermostat to "MAX"
for a few hours. Then reset the thermostat to the
desired
setting, usually
at
mid-setting.
CLEANING THE REFRIGERATOR
Always
keep
the
refrigerator
clean.
Cleaning
the
refrigera-
tor is
usually
done after it is defrosted or
put
into
storage.
To clean the interior liner of the
refrigerator,
use lukewarm
weak soda solution. Use
only
warm water to clean the finned
evaporator, gasket,
ice
tray
and shelves.
Note! Never use
strong
chemicals or abrasives to clean these
parts,
as the
protective
surfaces will be
damaged.
[It
is
important
to
keep
the area at the back of the
refrigerator
clean. Check the lower
vent,
upper
vent and area between
these
openings
for
any
obstructions such as bird/insect
nests,
spider
webs,
etc. Clean the coils on the back of the
refrigera-
tor. Use a soft bristled brush to dust off the coils.
Keep
the
refrigerator
area free from combustible
material,
gasoline
and
other flammable
vapours
or
liquids.
MAINTENANCE & SERVICE
Service and maintenance must be done on a
regular
schedule to
keep
the
refrigerator operating properly, efficiently
and
safely.
The service should
only
be
performed by
an
aurthorised
person.
This
appliance
must be serviced
by
an authorised
person.
We
recommend that an authorised service technician checks the
refrigerator
once a
year.
The "Installation and
operating
inst-
allations manual" should
always
be available.
14
Ensure
the
gas safety
shut-off valve is
working properly.
Make sure that the ventilation
openings
are unobstructed.
See
to it that
the
burner is clean and free
from combustable
material. All connections in the
LP
gas system
should be
checked for
gas
leaks. Connections can be tested for leaks
1. Shut off the
refrigerator by
pressing
and
holding
the
button for 3
seconds,
all indicator
light
will
be off.
using
a
soap
solution.
Do not use a naked flame!
If there is
any
suspicion
of
damage,
call for an authorised
service technician.
SERVICE
AND
SPARE PARTS
Service and
spare parts
are obtainable from
your
dealer or
Dometic
-
consult the
telephone directory.
REPLACING
THE HEATER
The
refrigerator
is
equipped
with two
electrical
heaters,
one
for 230-240
VAC
and one for 12 V
DC.
To
replace
the heater
proceed
as follows:
240 volt AC outlet. Disconnect
the
12
V
DC
power
to the
refrigerator.
2. Remove
the
refrigerator
from
the enclosure.
3. Disconnect the heater leads.
4. With a
pair
of
pliers,
unfold the
lug holding
the lid
of the boiler
casing
and
open
the lid.
5. Remove some insulation wool so that the heater is
accessible.
CAUTION
Do not use:
¢
A knife
or an ice
pick,
or other
sharp
tools
to remove frost from the freezer shelves. It
ean create a leak in the ammonia
system.
¢
A hot
air blower. Permanent
damage
could
result from
warping
the metal or
plastic
parts,
1.
Unplug
the
refrigerator power
cord from the 230-
Turn and lift the heater out of its
pocket.
Fit
the new heater into the
pocket.
Reconnect
the
heater
leads
at the
top.
NS
Put back the insulation and close the lid of the
boiler.
10. Reinstall
the
refrigerator
in
the enclosure.
11. Check all connections for
gas
leaks.
12. A
qualified gas
fitter should be
employed
13. Connect 230-240V
power
cord to the outlet
14.
Reconnect or turn on the
12 V
DC
power.
PERIODIC MAINTENANCE
This
work should
be made
by
a
qualified
service man.
CHECKING
THE
CONNECTIONS
Check all connections
in
the ULP
gas system
(at
the back of
the
refrigerator)
for
gas
leaks. The ULP
gas supply
must be
turned on.
Apply
a
non-corrosive bubble solution to
all
ULP
gas
connections. The
appearance
of bubbles indicates a leak
and should be
repaired immediately by
a
qualified
gas
fitter
CHECKING THE ULP GAS PRESSURE
The ULP
gas
pressure
should be checked and the main
regula-
tor
readjusted
if
pressure
is incorrect. The correct
operating
pressure
is
2,7
kPa. The correct
place
to measure the ULP
gas
pressure
is at the test
port just
ahead of the burner
jet.
PRESSURE TEST PORT
To Next Page
Loading...
