“More information https://www.caravansplus.com.au"
IMPORTANT
MES
operation
on 12 volt DC
!
CAUTION
Do
NOT
operate
the
refrigerator
on
12
volt when the
vehicle is
parked.
The
amperage
draw of the
12-volt
SWITCHING BETWEEN ENERGY SOURCES
When
switching
from one
energy
source to
another,
there are
some
delays implemented
in the AES
function.The
15 min.
delay
between
switching
off the
engine
and
starting gas
mode
is
intended
to
delay
the
starting
of
gas
mode
e.g.
when
stopping
at a
filling
station.
DC
heating
element can
discharge
a
battery
in a
very
short time. The installation of a 12-volt DC
operated
refrigerator requires
a
relay
to be installed on
the
tow vehicle or
in
the caravan. The
relay
will
auto-
matically
shut off the 12 volt
DC
power
to the
refrig-
erator when the
ignition
is turned off.
(See
fig.
9).
A
WARNING
It is not allowed to have a naked flame at a
gas filling
station. If
you
are not
sure,
that
your stop
is shorter than
15
min.,
you
are advised to set the ON/OFF
switch
(1)
to
"OFF",
when
stopping
at
a
filling
station.
ABNORMAL OPERATION
Refrigerator
Yellow
tipping
of the burner flame.
Sooting
up
area
surrounding
burner.
7 OF
Burner not
igniting properly.
Burner
failing
to remain
alight.
Breaker
Ignition
point
coil
Switch
key
Any
of the
following
are considered to be abnormal
_
Relay
_
operation
and
may
require
servicing:
FIG. 9
in
case the
appliance
fails to
operate
correctly,
contact an authorised Dometic service Centre.
CHANGING
BETWEEN
MES & AES FUNCTION
The control
system
function can be set in one of two functions.
(MES)
Manual
Energy
Selection
the default
setting
out of the box or
(AES)
Automatic
Energy
Selection.
The control function can be
changed
from one to the other
in
the
following way.
Note: The
D+
wire connection must be connected to
operate fully
in
AES function. The MES function
will
operate
with or without the D+ wire connection.
IMPORTANT
!
FOR THE INSTALLER
This
refrigerator
has dual function and
may
be
pre
set to the
required
function
(MES)
or
(AES)
function
during
or after the installation.
1.
MES
operation
(Manual Energy Selection)
is
the default
setting.
MES
lamp
will
be
lit at
start
up.
2. AES
operation
(Automatic Energy Selection)
is
optional.
If
AES function is
required
it
must be
pre
set
during
installation.
AES function
requires
the D+ wire on back of
refrigerator
to be connected to vehicle
charging
circuit. Once set
(see
step
4),
the AES
lamp
will
be
lit at start
up.
3. Connect
12 V
DC to the control circuit. Press and hold button for 3 seconds to start the
refrigerator
MES
lamp
will
remain
on.
4.
To
change
the
operating
function to AES or back
to
MES.
AES
AGG
MODE SET
MES
A
&
a
Press
and hold
andthe buttons
in
simultaneously
for 4
seconds. Control
system
will
move
to
AES
function,
AES
lamp
will be lit
(MES off). Repeat
this
process
to move the
system
back to
MES
function MES
lamp
will be lit
(AES
lamp
off).
11
To Next Page
Loading...
