“More information https://www.caravansplus.com.au"
CONNECTIONS
Gas connection 1/8 BSP
=
Vehicle
battery
Only
required
12 VDC
house
operation.
D
The
refrigerator
is
equipped
with
two
12 volt
DC
connections
and one D+ connection
(
D+ is
only requtred
if automatic function
has
been
preset
)
A. D+
Connection
is
required
if the
(AES)
control
option
is
preset
.
The
D+
connection is not
required
if
the
(MES)
control
option
is
preset. (MES
is the default
mode)
If
required
this D+ connection must be connected to a 12 V
positive
DC
output
from the vehicle
charging
circuit.
B.
Connection
to
permanent
12
volt DC house
battery.
C.
Connection
to vehicle
battery.
This connection
supplies
the 12 volt DC
heating
element.
D.
AC
(240)
volt
connection.
E.
Universal
gas
connection.
UNIVERSAL
LP GAS CONNECTION
The
gas
installation and
servicing
must be carried out
by
an
authorised
person
and conform to all relevant local
require
-.
ments.
The
refrigerator
is not
designed
for
operation
on town
gas
or
natural
gas
but for
operation
on universal
LP
gas,
the
pressure
of which must be
2,75
kPa.
Check that this is stated on
the data
plate.
The
gas supply system
must
incorporate
an
approved gas pressure regulator
to maintain a
supply pressure
of
2,75
kPa.
The
supply pipe
should be of
copper.
If other material is used
it must be of a
type approved
for
use with
continuously
operat
ing bottle-gas appliances
and have threaded connections throu
gh
out.
All connectors etc. should be
of
a
type specifically designed
for the
type
and diameter of the connection
pipe
used,
and
screwed
joints
should be sealed with a
joining compound ap-
proved
for use with
bottle-gas.
The
gas supply pipe
should be connected to the
gas
valve at
the
bottom of the
refrigerator,
by
means of a suitable
threaded
coupling.
The
gas
valve is furnished with an ISO 7/1
-
Rp
1/8 internal
pipe
thread connection.
In
making
the connection to the
refrigerator,
a union
gas
cock
of an
approved bottle-gas type
must be
incorporated
in the
supply
line in a
position
which is
readily
accessible to the
user. For eventual
servicing purposes,
the union should be
positioned
so as not to
prevent
the
refrigerator
from
being
readily
withdrawn.
A
Before
leaving,
the installer should:
Check
all
connections
for
gas
leaks with
soap
and water.
DO NOT use a naked flame for
detecting
leaks!
Ignite
the
burner to ensure correct
operation
of the
controller,
burner
D+
Continuous
connection 12V DC
only,
Minimum 6 mm wire
and
ignition.
Instruct the user
on
the correct method of
operation.
In case the
appliance
fails to
operate
correctly
after all checks
have
been carried
out,
contact the authorised
service
provider
in
your
area.
ifor
AES
Flexible
cord
battery supply
A
AC
ELECTRICAL CONNECTION
The electrical installation must be carried out in a
proper
and
durable
manner,
taking
into account all relevant
regulations
and codes of
practice.
For
mains
voltage operation,
it is
important
that the circuit to
and in the caravan
is
effectively
earthed.
The
refrigerator
is
equipped
with a
three-prong (grounding)
plug
for
your
protection against
shock hazards
and
should
be
plugged directly
into
a
properly grounded threeprong
socket.
Note! Do not cut or remove the
grounding prong
from this
plug.
The free
length
of the cord is 6 ft.
(1,8 m).
It is recommended
the socket
be
placed
on the left side of the
refrigerator
(viewed
from the
rear)
and
approximately
4-6 inches
(100-
150
mm)
from the floor. This will allow
easy accessibility
through
the vent door.
230-240 V
supplies
Check
that the
voltage
stated on the data
plate
is the same
as the main
voltage
in use
(230-240 V).
Plug
the 230-240 V
refrigerator power
cord into an
easily
accessible
wall socket.
Electrical leads must be routed and secured so that
they
can-
not come into contact with hot or
sharp parts
of the
refrigera-
tor.
7
To Next Page
Loading...
