Dormakaba ED50 - Installation Instructions Manual

78 pages

Save Page as PDF

To Next Page

ED50/ED100/ED250

Swing door operators

Installation Instructions

DL4616-004 – 11-2022

| EN |

Main Page

Table of Contents2
General Information4
Product Overview5
Maximum Door Weights and Door Installation5
Single Door Configuration Examples6
Double Door Configuration Examples6
ED50 Operator7
ED100/ED250 Operator7
Accessory Terminals, Guide Pin, Backplate Screw Kit7
Kit, ED Operator Labels8
Fine Cover Kits9
Fine Cover Kit Hardware11
Axle Extensions, ED50/ED100/ED25012
Push Arm Door Stop - Option12
Push Arm Kits13
Pull Arm Kits13
Arm Screw Kits13
Optional Key Switch Panels14
Double Door ED50/ED100/ED25014
Operator Connection Cables14
Technical Data15
ED50/ED100/ED250 Operator Technical Data15
Operating Specifications - ED100/ED25016
Operating Specifications - ED5016
Torque Overview; ED100/ED25017
Terminal Board Interfaces18
ED50/ED100/ED250 Terminal Board Interfaces18
ED50/ED100/ED250 Door Signage19
Ansi/Bhma A156.1019
ED50/ED100/ED250 Low Energy Operator - ANSI/BHMA A156.1919
Safety Label, Automatic Swing Doors20
Safety Label, Low Energy Swing Doors20
Door Signage, Full Energy Single Swing Door21
Door Signage, Low Energy Swing Door21
Door Signage, Full Energy Double Door22
Door Signage, Full Energy Double Egress Door23
Door Signage, Low Energy Double Doors24
Recommended Tools and Torque Chart25
Recommended Tools25
Standard Tightening Torque25
Drill Bits25
Installation Templates26
ED50/ED100/ED250 Installation Templates26
ED50/ED100/ED250 Operator Installation31
Installation Preparation31
Remove Mounting Plate from ED50/ED100/ED250 Operator32
Customer 115 Vac Connection to Mounting Plate Terminal Block33
Mounting Plate Attachment to Jamb or Wall35
Connect Customer 115 Vac to Mounting Plate Terminal Block36
Route Accessory Wiring to Mounting Plate36
Remove Protective Film Strips from Operator37
Install ED100/ED250 Operator Onto Mounting Plate38
Install ED50 Operator Onto Mounting Plate39
Push Arm Installation Templates40
Pull Arm Assemblies43
Pull Arm Hardware43
Install Hardware into Track44
Assemble Slide Shoe44
Assemble Deep Pull Arm (DK4709-12X Arm Assembly), if Used45
Deep Pull Arm Installation46
Standard Pull Arm Installation48
Operator Spring Tension50
Set ED50/ED100/ED250 Operator Spring Tension50
ANSI/BHMA Standards51
ANSI/BHMA A156.10 Power Operated Pedestrian Doors51
ANSI/BHMA A156.19 Low Energy Power Operated Doors52
Install Door Signage53
Fine Cover, End Caps and Spindle Caps53
Fine Cover End Cap and Spindle Installation53
Maintenance54
Safety Label, Automatic Swing Doors54
Safety Label, Low Energy Swing Doors54
Arm Fasteners - Torque Requirements55
Companion Door Installation56
ED100/ED250 Companion Installation Templates56
8616 Closer and Adaptor58
Companion Door 8616 Door Closer Data58
Select Installation Template59
Assemble ED100/ED250 and Closer Backplates59
Companion Door, Push Arm Installation60
Mount Backplate, Push Arm Application60
Install 8816 Closer on Backplate - Push Arm Mounting61
Push Arm Installation62
Companion Door, Pull Arm Installation64
Mount Backplate, Pull Arm Application64
Install 8816 Closer on Backplate - Pull Arm Mounting65
Pull Arm Installation66
8816 Closer Adjustments69
8816 Door Closer Adjustments69
Appendix A - Fine Cover Professional Cover Kits70
Professional Cover Kit DK3401-05X Installation Instructions - Single Door70
Professional Cover Kit DK3401-07X Installation Instructions - Pair73
Appendix B - Key Switch Wiring Diagrams75
Connector75
B2.1 DX4604-11C Key Switch Panel76
Appendix C - Knowing Act Switch Wiring77
Diagrams77
C1.1 Knowing Act Switches77
C1.2 Knowing Act Switch Wiring Diagram77

Dormakaba ED50 - Installation Instructions Manual

Table of Contents

Other manuals for Dormakaba ED50

Related product manuals