Dräger Atlan A300 - Checking the operational readiness

Dräger Atlan A300

332 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Instructions for use | Atlan A300, A300 XL, A350, A350 XL SW 1.0n 259

Reprocessing

13.12.2 Checking the operational readiness

Prerequisite: The device is assembled and prepared ready for operation.

► Check the operational readiness with a system test.

Observe the following information: "Tests", page 126.

Table of Contents

Default Chapter3
- Table of Contents3
1 Information about this Document7
- Typographical Conventions7
- Use of Terms7
- Illustrations7
- Trademarks7
2 Safety-Related Information9
- Intended Use9
- Indications9
- Contraindications9
- Environments of Use10
- Essential Performance Features10
- User Group Requirements11
- Information on Safety Instructions and Precautionary Statements11
- Safety Instructions12
- Additional Information14
3 Overview15
- Hardware15
- Functional Scope31
- Gas Flow Diagram42
4 Assembly and Preparation45
- Safety Instructions45
- Mounting of Accessories52
- Before First Operation55
- Intrahospital Transport59
- Gas Supply59
- Connecting to the Gas Scavenging System65
- Preparation for an Operation Day / after Cleaning and Sterilization67
- Selecting and Connecting Patient-Specific Accessories67
- Connecting and Replacing Consumables75
5 Operating Concept79
- Screen79
- Color Concept83
- Selecting and Setting84
6 Getting Started86
- Safety Instructions86
- Turning on the Device86
- Checking the Device Configuration86
- Checking the Operational Readiness87
- Emergency Start-Up88
7 Operation89
- Safety Instructions89
- Starting the Therapy93
- Adjusting the Therapy96
- Special Forms of Therapy100
- Using Fields with Special Functions103
- Customizing the Screen Display107
- Displaying Additional Data113
- Setting the Volume115
- Adjusting the Alarms116
- Changing the Patient Data119
- Exporting Data119
- Other Settings120
- Ending the Therapy122
- Change of Patient124
8 Tests126
- Status of the Device Functions126
- Available Test Types127
- Performing the Tests127
- Checklist in the Walk-Through Mode136
9 Ending Operation151
- At the End of the or Day151
- Storing the Device151
- Disconnecting the Mains Power Supply151
10 Alarms152
- Safety Instructions152
- Displaying Alarms152
- Response to Alarms154
- Adopting Alarm Settings When Changing the Ventilation Mode159
- Alarm Delay and Alarm Escalation160
- Activation of Alarms after Breath Detection163
- Intelligent Alarm Behavior164
11 Configuration165
- Device Settings165
- Setting the Date and Time165
- Specifying the Start Settings166
- Transferring Device Configurations181
- Activating Software Options182
- Overview of Configurable Screen Contents184
12 Troubleshooting190
- Leakage190
- Power Supply Failure191
- Failure of the Gas Supply192
- Failure of Fresh-Gas Delivery (Electronically Controlled Gas Mixture)194
- Failure of the Piston Ventilator195
- Failure of the O 2 Sensor195
- Flow Measurement Failure198
- Screen Fault or Failure of the Graphical User Interface198
- Complete Failure198
- Problems with the Active Anesthetic Gas Receiving System (AGS)199
- Cylinder Pressure Reducer201
- Support Request201
- Alarm - Cause - Remedy201
13 Reprocessing222
- Safety Instructions222
- Information on Reprocessing223
- Classifications for Reprocessing224
- Reprocessing List225
- Reprocessing Procedures225
- Preparation227
- Surface Disinfection with Cleaning229
- Disassembly230
- Disassembling the Breathing System238
- Machine Reprocessing242
- Fitting and Assembly249
- Preparation before the Next Use258
- Brief Instructions for Reprocessing260
14 Service262
- Safety Instructions262
- Definition of Service Terminology262
- Inspection262
- Maintenance265
- Repair265
15 Disposal266
- Safety Instructions266
- Disposing of the Device266
- Disposing of Accessories266
16 Technical Data267
- Safety Instructions267
- General Information268
- Ambient Conditions268
- Fresh-Gas Delivery269
- Fresh-Gas Delivery with Electronically Controlled Gas Mixer269
- Fresh-Gas Delivery with Mechanically Controlled Gas Mixer270
- Ventilator270
- Breathing System272
- External Fresh-Gas Outlet274
- Anesthetic Gas Receiving System (AGS)274
- Active AGS274
- Passive AGS275
- Measuring Systems and Displays275
- Gas Measurement279
- Gas Measurement with279
- Gas Measurement with O281
- Sensor281
- Operating Characteristics283
- Interfaces and Ports287
- Relevant Standards289
- Diagrams290
- EMC Declaration291
- Device Combinations293
- Emission of High-Frequency Energy293
- Connections to IT Networks294
- Open-Source Software297
17 Principles of Operation297
- Safety Instructions297
- Description of the Ventilation Modes298
- Description of the Ventilation Drive307
- Improving the CO 2 Measurement by Means of an HME Filter308
- Minimum O 2 Delivery310
- Influence of Patient Category, Weight, and Age on Device Behavior311
- Support of Infinity ID Accessories312
- Schematic Illustration of the Acoustic Signals313
18 Annex314
- Abbreviations314
- Symbols317
- Product Labels322
- Overview of the Menu Structure323
19 Password325
- Configuration Password for Atlan A300, A300 XL, A350, A350 XL Software 1.0N325
Index327

Other manuals for Dräger Atlan A300

Supplement72 pages

Supplement Manual72 pages

Related product manuals

Dräger Atlan A350

Dräger Atlan A350 XL

Preview: Dräger Atlan

Preview: Dräger Atlan A100

Dräger Atlan A100

Preview: Dräger AGS

Preview: Dräger Apollo

Preview: Dräger Perseus A500

Dräger Perseus A500

Dräger Aquapor H300

Preview: Infinity Acute Care System M540

Infinity Acute Care System M540

Infinity Acute Care System Workstation Critical Care

Preview: Dräger Savina

Preview: Dräger Savina 300

Dräger Savina 300