16
EA2;@6<;<?1@
3 .; 2EA2;@6<; 0<?1 6@
;202@@.?F . 0<?1 D6A5
.12>B.A2@6G2 0<;1B0A<?@A5.A 6@ 0.=./92
<30.??F6;4A520B??2;A;202@@.?F3<?F<B?
A<<9 :B@A /2 B@21 This will prevent
excessive voltage drop, loss of power or
overheating. Grounded tools must use 3-wire
extension cords that have 3-prong plugs and
receptacles.
!"&The smaller the gauge number, the
heav i er the cord.
$" !%,%"*&!%"!"$%
("&&$!&!'$$!&&""%
&<<9K@
:=2?2
$.A6;4
<?1%6G26;)
)6?2%6G2@6;::
2-6
6-8
8-10
10-12
12-16
18 16 16 14 0.75 0.75 1.5 2.5
18 16 14 12 0.75 1.0 2.5 4.0
18 16 14 12 0.75 1.0 2.5 4.0
16 16 14 12 1.0 2.5 4.0 —
14 12 —— ————
25 50 100 150 15 30 60 120
<?12;4A56;22A <?12;4A56; 2A2?@
.6;A2;.;02;3<?:.A6<;
%2?C602
#?2C2;A6C2 :.6;A2;.;02
=2?3<?:21 /F B;.BA5<?6G21
=2?@<;;29 :.F ?2@B9A 6; :6@=9.06;4 <3
6;A2?;.9D6?2@.;10<:=<;2;A@D56050<B91
0.B@2 @2?6<B@5.G.?1 We recommend that
all tool service be performed by a Dremel
Service Facility.
&< .C<61 6;7B?F 3?<:
B;2E=20A21 @A.?A6;4 <?
2920A?60.9@5<08.9D.F@?2:<C2=9B43?<:
D.99 <BA92A /23<?2 =2?3<?:6;4 @2?C602 <?
092.;6;4
$!%
Model 6800 has ball bearing construction.
Under normal use no additional lubrication is
required.
92.;6;4
&< .C<61 .00612;A@.9D.F@
16@0<;;20A A52 A<<9 3?<:
A52 =<D2? @B==9F /23<?2 092.;6;4 <?
=2?3<?:6;4.;F :.6;A2;.;02 The tool may
be cleaned most effectively with compressed
dry air. 9D.F@ D2.? @.32AF 4<4492@ D52;
092.;6;4A<<9@D6A50<:=?2@@21.6?
Ventilation openings and switch levers must be
kept clean and free of foreign matter. Do not
at tempt to clean by inserting pointed objects
through openings.
2?A.6; 092.;6;4 .42;A@
.;1 @<9C2;A@ 1.:.42
=9.@A60 =.?A@ Some of these are: gasoline,
carbon tetrachlo ride, chlo rinated cleaning
solvents, ammonia and house hold detergents
that contain ammonia.
WARNING
!
!
WARNING
!
WARNING
CAUTION
!
!
WARNING
DM 2610010088 02-10:DM 2610010088 02-10 2/26/10 1:02 PM Page 16
To Next Page
Loading...
