EasyManua.ls Logo

DSC 3G2080E - User Manual

DSC 3G2080E
72 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
TL280LE(R) / TL280LE-EU /
TL280LE-LAT / TL280LE-AU
Internet and LTE/HSPA Dual-Path Alarm
Communicator
LE2080(R) / LE2080-EU / LE2080-
LAT / LE2080-AU
LTE/HSPA Alarm Communicator
3G2080(R)E
HSPA Cellular Alarm Communicator
TL2803G(R)E
Internet and HSPA Dual-Path Alarm Communicator
TL280(R)E
Internet Alarm Communicator
Installation Manual 5.X
Warning: This manual contains information on limitations regarding product use and function and information on the
limitations as to the liability of the manufacturer. The entire manual should be carefully read.
Please note that not all models and features listed are available in all markets.

Table of Contents

Other manuals for DSC 3G2080E

Preview: Installation Manual
Installation Manual60 pages

Questions and Answers

  • R
    Robert DavisNov 26, 2025
    Why is the yellow LED flashing 7 times on my DSC 3G2080E Security System?
    • C
      carmensmithNov 26, 2025
      If the yellow LED on your DSC Security System is flashing 7 times, it means the receiver is not available. First, ensure that the Ethernet path has Internet connectivity. If you're using a static IP address, confirm that the gateway and subnet mask are entered correctly. If the network has a firewall, ensure that the programmed outgoing ports are open (default UDP port 3060 and port 3065). Ensure that all the receivers are programmed for DHCP or have the proper IP address and port number. Ensure the cellular receiver APNs have been programmed with the access point name provided by the cellular provider. If Common Mode is used, and only one path is initialized while the other path is not successful, generate a manual test transmission over both paths or power cycle the communicator to recov...
  • M
    morserebeccaAug 25, 2025
    Why is the yellow LED on my DSC 3G2080E solid?
    • S
      Steven GuerreroAug 25, 2025
      If the yellow LED on your DSC Security System is solid, it means there is no signal. Verify that cellular network service is active in your area. Also, make sure the antenna is securely connected to the radio. Check that the antenna stub cable is securely connected to the radio. If you're using an external antenna, ensure it's securely screwed onto the antenna cable connector and inspect the external antenna for any damage or shorts.
  • A
    Andrea VasquezAug 25, 2025
    How to fix yellow LED flashing 6 times on DSC 3G2080E?
    • N
      Nicole MathisAug 26, 2025
      If the yellow LED on your DSC Security System flashes 6 times, it indicates an Ethernet trouble. Start by checking with your ISP to confirm that Internet service is active in your area. Ensure the Ethernet cable is securely inserted into both the RJ45 jack of the communicator and the hub/router/switch. Verify that the link light on the hub/router/switch is ON; if it's OFF, restart the hub/router/switch. If DHCP is in use, confirm that the unit has been assigned a valid IP address from the server. If the problem persists, try replacing the Ethernet cable and RJ45 connector.
  • E
    Edward NewmanAug 27, 2025
    What to do if my DSC 3G2080E has no indication?
    • M
      Melissa WilliamsAug 27, 2025
      If your DSC Security System shows no indication (no lights, no response), the cause might be no power. Check the power connections between the panel and the communicator. Also, confirm that the PC-LINK cable is properly installed between the communicator and the panel.
  • M
    Miguel KellyAug 28, 2025
    What does it mean when all LEDs are flashing on my DSC 3G2080E Security System?
    • H
      Heather JenkinsAug 28, 2025
      If all the LEDs on your DSC Security System are flashing together, it indicates a boot loader failure. To resolve this, disconnect and then reconnect the power to the communicator module.
  • J
    Jamie TaylorSep 16, 2025
    What does it mean when the yellow LED flashes 9 times on my DSC Computer Hardware?
    • G
      Gregg AcevedoSep 17, 2025
      If the yellow LED flashes 9 times, it indicates an FTC trouble. Restart the system, if trouble persists, contact the dealer.
  • M
    michaeljohnsonSep 14, 2025
    What does it mean when the red and yellow LEDs are flashing together on my DSC Computer Hardware?
    • D
      Donna WilliamsSep 14, 2025
      If the red and yellow LEDs are flashing together, the unit is still initializing. Please wait while the unit gets its programming and establishes a connection to all programmed receivers.
  • T
    Tara CarrollSep 15, 2025
    What does it mean when the yellow LED flashes 8 times on my DSC Computer Hardware?
    • K
      Kimberly MullenSep 15, 2025
      When the yellow LED flashes 8 times, it indicates a receiver supervision trouble. This trouble is indicated when supervision is enabled and the unit is not able to successfully communicate with the receiver. If this trouble persists, contact the central station.
  • A
    andrea46Sep 6, 2025
    What to do if my DSC Computer Hardware shows no indication?
    • D
      David PerezSep 6, 2025
      If your DSC Computer Hardware shows no indication, the issue might be due to a lack of power. Check the power connections between the panel and the communicator. Also, confirm that the PC-LINK cable is properly installed between the communicator and the panel.
  • C
    Charles TuckerSep 3, 2025
    Why are only the green LEDs flashing on my DSC 3G2080E Security System?
    • A
      Austin MartinSep 4, 2025
      If only the green LEDs are flashing on your DSC Security System, it means the hardware default jumper is installed and must be removed.

Summary

Installer Warnings and Guidance

Installer Notes and Responsibilities

General Product Overview

User Safety Information

Instructions for users on safe operation, servicing, and handling of the equipment.

Supported Model Information

Lists the alarm communicator models covered by the manual and their regional specifications.

Product Features and Specifications

Key Product Features

Detailed Technical Specifications

Provides technical specifications for the communicator, including standards compliance.

EN50131-1 Installation Requirements

Programming options required for EN50131-1 compliant installations.

Communicator Installation Configuration

Compatible Receivers and Panels

Pre-Installation Configuration Steps

Ethernet Cable Installation

Instructions for installing the CAT 5 Ethernet cable for TL models.

SIM Card and RS-232 Cable Installation

SIM Card Insertion and Removal

Communicator Placement and Signal Testing

Placement Test Procedure

Procedure to test cellular antenna location suitability for radio operation.

Initial Panel Programming and Activation

Initial Panel Programming Steps

Steps for initial programming of the panel and communicator.

Activation with C24 Communications

SMS Command and Control Features

SMS Command List

Communicator Status LED Indicators

Yellow Trouble LED Interpretation

Meaning of the yellow trouble LED and its flash codes.

Trouble Indicators and LED Status

Panel Supervision and Cellular Troubles

Ethernet and Receiver Troubles

Supervision, FTC, and Module Troubles

Red Network Connection Status LED

Green Signal Strength LEDs

Communicator Reset and Firmware Update

Factory Defaults Reset Procedure

Steps to restore the communicator to its factory default settings.

Firmware Update Process

Information on how to update the communicator's firmware.

Communicator Troubleshooting Guide

Trouble Indications and Solutions

Table detailing trouble indications, possible causes, and solutions.

Ethernet;Cellular Programming Options

System Options Configuration

Configuration settings related to the system's operation and network.

Ethernet Network Settings

Settings for Ethernet IP Address, Subnet Mask, and Gateway.

System Toggle Options

Communication and System Settings

Account Code and Communications Format

Communications Reporting Codes

System Test Transmission Configuration

Primary;Secondary Receiver Test Options

Unique Primary;Secondary Receiver Tests

Ethernet Receiver Configuration

Ethernet Receiver 1 Options

Ethernet Receiver 2 Options

Cellular Receiver Configuration

Cellular Receiver 1 Options

Cellular Receiver 2 Options

Cellular Network and SMS Options

Cellular Network Settings

SMS Event Notification and Control

Integration Settings

Session 1 Integration Toggle Options

Diagnostic Testing and System Information

Receiver Diagnostic Testing Procedure

Procedure to force test transmissions to verify communications paths.

Response Code Descriptions and Actions

Communicator Status and Signal Strength

Communicator Status Interpretation

Details on how communicator status is displayed and interpreted.

Radio Signal Strength Indicators

Table showing radio signal strength indicators and actions.

Network Usage and Security Recommendations

DSC 3G2080E Specifications

General IconGeneral
Weatherproof RatingIP66
Communication TechnologyEthernet
Resolution1920x1080 (Full HD)
Video CompressionH.264
IR RangeUp to 30m
Power SupplyDC 12V
Day/NightYes (ICR)
Min. Illumination0.01 Lux
Network ProtocolsTCP/IP, HTTP, DHCP, DNS, DDNS, RTP, RTSP, PPPoE, SMTP, NTP, HTTPS, FTP
InterfaceRJ45
Operating Conditions-30 °C to 60 °C (-22 °F to 140 °F), humidity: 95% or less (non-condensing)

Related product manuals