What should I do if all indicators are flashing simultaneously on my DSC TL260GS?
If all indicators on your DSC Cell Phone are flashing at the same time, it indicates a boot loader failure. Disconnect and then reconnect power to the communicator module.
What does it mean when both green LEDs are flashing rapidly at the same time on my DSC Cell Phone?
If both green LEDs are flashing rapidly at the same time on your DSC Cell Phone, it means the hardware default jumper is still in place and needs to be removed.
General| SIM | Dual SIM |
|---|---|
| Display | 2.4" |
| Resolution | 240 x 320 |
| Rear Camera | VGA |
| Front Camera | No |
Procedure for obtaining warranty service and returning products for repair.
List of conditions that will void the product's warranty.
Specifies items and situations not covered by the warranty.
Details procedures and costs for repairing products outside the warranty period.
Important information for installers to convey to system users regarding system limitations.
Discusses circumstances where the system may fail to provide protection.
Addresses the possibility of criminals developing techniques to bypass system features.
Explains how intruders might circumvent the security system's detection.
Explains the impact of power interruptions on system operation and potential damage.
Discusses battery life, factors affecting it, and low battery monitoring.
Describes potential interference with wireless signals.
Explains limitations and reasons why smoke detectors might not alert occupants.
Compliance statement and guidelines for using the equipment to avoid interference.
Compliance statement for digital apparatus according to Canadian standards.
Outlines the terms and conditions governing the use of the software product.
Details the rights granted to the user for software installation, storage, and backup copies.
Specifies limitations on reverse engineering, decompilation, and modifications.
States that the software is provided 'as is' without express or implied warranties.
DSC is not responsible for issues arising from hardware changes or interactions.
Limits DSC's liability and states that warranty reflects risk allocation.
Reaffirms that this warranty is exclusive and supersedes all others.
Defines the exclusive remedy and limits liability for damages.
Lists and briefly describes the available communicator models.
Highlights the main functionalities and capabilities of the communicator.
Steps and contact information for activating the communicator with CONNECT 24.
Step-by-step guide for installing the communicator with specific control panels.
Wiring diagram for TL260GS/GS2060 and optional GSM antenna kits.
Instructions for installing the communicator with the PC9155 control panel.
Options for external GSM radio antenna kits for the PC9155 enclosure.
Details programming options for telephone numbers and communication paths.
Specifies the setting for communication format (SIA FSK).
Explains the setting for T-Link Interface Enable.
Configuration options for communication paths on the PC9155 panel.
Specifies the setting for communication format (SIA).
Explains the function and flash codes of the Trouble Status LED.
Describes the 'Panel Supervision Trouble' condition indicated by the LED.
Explains specific trouble conditions like Lockout, GSM, Ethernet, and Receiver issues.
Details troubles related to FTC, Connect24, Remote Programming, and Firmware Updates.
Explains the function and activation of the Network Connection Status LED.
Details how signal strength LEDs indicate radio signal levels.
Steps for installing an antenna extension kit to improve signal strength.
Instructions on how to use the hardware default jumper to reset options.
Lists communicator trouble conditions and user actions for the 9155 panel.
Describes the 'Loss of Time and Date' trouble and how to resolve it.
Process and requirements for UL remote flash updates.
Configuration settings for Ethernet IP, supervision, and system toggles.
Settings for installer code, DLS ports, and Ethernet/GPRS receiver configurations.
Settings for GPRS APN, login credentials, and viewing system information.
Detailed settings for Ethernet IP Address, Subnet Mask, and Gateway IP Address.
Configuration for receiver supervision intervals and system-wide toggle options.
Configuration of installer code and DLS connection ports for the communicator.
Settings for account code, DNIS, and IP address of the first Ethernet receiver.
Configuration of local and remote ports for Ethernet Receiver 1.
Settings for account code, DNIS, and IP address of the second Ethernet receiver.
Configuration of local and remote ports for Ethernet Receiver 2.
Settings for account code, DNIS, and IP address of GPRS Receiver 1.
Configuration of port and APN for GPRS Receiver 1.
Settings for account code, DNIS, and IP address of GPRS Receiver 2.
Configuration of port and APN for GPRS Receiver 2.
Settings for GPRS login credentials and viewing system information.
Options to confirm firmware, IP, SIM, phone, IMEI, and MAC details.
Option to reset programming to factory defaults.
To Next Page
