To Next PageTo Next PageWhy does the Duraflame Indoor Fireplace power cord get warm?
If the Duraflame Indoor Fireplace power cord gets warm, it could be due to normal operation. Check your heater cord and plug connections. Faulty wall outlet connections or loose plugs can cause overheating. Ensure the plug fits tightly in the outlet. If the outlet or faceplate gets HOT, stop using the heater and have an electrician check the outlet.
What to do if the Duraflame Indoor Fireplace heater shut off and won't come back on?
If your Duraflame Indoor Fireplace heater shuts off and won't come back on, the manual reset may have been triggered. Turn the power to “OFF” and unplug the unit for 5 minutes. After 5 minutes, plug it back in and operate as normal. If the problem persists, contact customer service.
Why is my Duraflame Indoor Fireplace remote control is not working?
If the Duraflame Indoor Fireplace remote control is not working, try these steps: * Change the remote batteries. * Operate the remote at a slow, measured pace, pressing buttons gently. * Ensure you are within 20 feet of the appliance and pointing the remote at the control panel.
What to do if Duraflame Indoor Fireplace flame effect works but heater function does not and the emberbed flashes when the heater button is pressed?
If the flame effect works but the Duraflame Indoor Fireplace heater function does not, and the ember bed flashes when the heater button is pressed, the heater might be disabled. To re-enable it, turn the power on, then press and hold the heater button on the control panel for 10 seconds. The ember bed lights will flash multiple times once it's re-enabled.
Why Duraflame Indoor Fireplace unit continues to run after reaching set temperature/or powering of.f?
If your Duraflame Indoor Fireplace continues to run after reaching the set temperature or powering off, it is normal operation. The unit will continue to run for several minutes before shutting down, blowing cool air. The duration varies based on heating.
What to do if Duraflame Indoor Fireplace flame efef ct operates, but heater does not blow warm air?
If the flame effect operates, but the Duraflame Indoor Fireplace heater does not blow warm air: * Try turning the HEATER button ON/OFF several times to ensure it is in the ON position. * Make sure the TEMPERATURE knob is set to the maximum setting.
How to fix Duraflame Indoor Fireplace logs glow, flame efef ct does not work?
If the logs glow but the Duraflame Indoor Fireplace flame effect does not work, check whether the Flame Generator drive motor is running. If not, call customer service.
Locates the serial number on the fireplace back and explains its importance for warranty registration.
Details the electrical specifications of the fireplace, including voltage, amps, and wattage.
Provides essential safety guidelines for using the appliance, including handling hot surfaces and keeping materials away.
Covers electrical safety, proper grounding, avoiding extension cords, and preventing hazards like fire and shock.
Details restrictions on use, such as not using outdoors, in bathrooms, or for drying clothes, and preventing blockages.
Illustrates and labels the controls on the fireplace's main unit and remote control for operation.
Explains how to use power, adjust flame, operate the heater, thermostat, and emberbed effects.
Addresses common problems like no power, flame effect not working, or heater not blowing warm air.
Provides solutions for remote control issues, unit shutdown problems, and power cord warmth.
Lists and illustrates the main parts of the fireplace for identification and assembly.
Provides instructions on cleaning the fireplace trim and emphasizes safety during maintenance.
Details FCC/IC compliance, potential interference, and measures to resolve reception issues.
Instructs on proper battery types, replacement, installation, and disposal for the remote control.
Outlines the terms, conditions, exclusions, and voiding factors for the product's one-year limited warranty.
Provides customer service contact details and information needed for inquiries or assistance.
General| Type | Electric Fireplace |
|---|---|
| Voltage | 120V |
| Remote Control | Yes |
| Adjustable Thermostat | Yes |
| Overheat Protection | Yes |
| Color | Black |
| Heating Area | 400 sq ft |
| Product Type | Electric Fireplace |
| Material | Metal |
| Flame Effect | Realistic Flame Effect |
