6
7 - NICKEL CYCLE CHARGING
1. Connect the banana plugs of the battery adapter cable to the Power Output Black (–) and
Power Output Red (+), making sure that the positive and negative connectors are not reversed.
2. Connect the battery connector to the battery adapter cable.
3. Press the Left and Right Arrows on the LCD Touch Screen to scroll through the main menu
screens until you reach Program Select=Ni-MH/Ni-Cd.
Program select=NiMH
CHG DCHG
N i M H
CYCLE
4. Press CYCLE.
NiMH CYCLE [1/2]
Capacity : 50mAh
CHG Curr. : 0.1A
DCHG Curr. : 0.1A
DCHG End Volt : 0.10V
Press&Hold : CYCLE
BACK SELECT
5. Press a parameter to highlight that parameter.
6. Press the Up and Down Arrows to edit the parameter.
7. Press Select to save the parameter.
8. Press the top right of the LCD Touch Screen to get to the next set of parameters.
9. Once the parameters are at the desired settings, press and hold CYCLE.
10. The charger will check the battery and charger settings and cycle charging will begin. The
charger will beep and display the following screen:
NiMH CYCLE 001:56S
Capacity : 47mAh
Current : 0.0A
Voltage : 8.00V
Resistance : ****mΩ
Peak Temp. : No sens
11. Press the arrow in the top right of the LCD Touch Screen to see the rest of the Cycle information.
12. Press CYCLE to see the voltage and amperage applied to each cycle.
Data NiMH = Cycle 1/1
--CHG-- --DISCHG--
00.00Vp 00.00Va
00000mAh 00000mAh
13. Press Graph to see the battery voltage graph. Press Back to return to the charging screen.
14. Press STOP at any time to stop charging.
15. When cycle charging is complete, the charger will sound a series of beeps and display the
following screen:
NiMH DONE 026:01S
Capacity : 671mAh
Current : 0.0A
Voltage : 9.25V
Resistance : 14mΩ
Peak Temp. : No sens
16. Disconnect the battery from the charger.
CAUTION: The Pb charge program menus are to be used ONLY for the charging and
discharging of Pb battery packs. Charging other battery types using the Pb charge
programs will damage the battery or the charger.
8 - PB CHARGING
1. Connect the banana plugs of the battery adapter cable to the Power Output Black (–) and
Power Output Red (+), making sure that the positive and negative connectors are not reversed.
2. Connect the battery connector to the battery adapter cable.
3. Press the Left and Right Arrows on the LCD Touch Screen to scroll through the main menu
screens until you reach Program Select=Pb.
Program select=Pb
CHG DCHG
4. Press CHG.
Pb CHARGE
Pack. Volt. : 2V/1P
Capacity : 50mAh
Current : 0.1A
Press&Hold : CHARGE
5. Press a parameter to highlight that parameter.
6. Press the Up and Down Arrows to edit the parameter.
7. Press Select to save the parameter.
8. Once the parameters are at the desired settings, press and hold CHARGE.
9. The charger will check the battery and charger settings and display the following screen:
Pb Charge Confirm
-Connect- -Check-
Input • • • • OK Set: 6P
BATT. • • • • OK Read: 5P
10. Press START. The charger will beep and display the following screen:
Pb CHG 000:16S
Capacity : 8mAh
Current : 1.7A
Voltage : 14.69V
Resistance : ****mΩ
Peak Temp. : No sens
11. Press the arrow in the top right of the LCD Touch Screen to see the rest of the charging
information.
12. Press Graph to see the battery voltage graph. Press Back to return to the charging screen.
Data Pb = Graph
14.68V 000:12S
BACK
13. Press STOP at any time to stop charging.
14. When charging is complete, the charger will sound a series of beeps and display the following screen:
Pb DONE 000:19S
Capacity : 8mAh
Current : 1.7A
Voltage : 11.60V
Resistance : ****mΩ
Peak Temp. : No sens
15. Disconnect the battery from the charger.
To Next Page
Loading...
Need help?
General
