Eaton EX 2200 RT 3U - User Manual

Eaton EX 2200 RT 3U

66 pages

To Next Page

To Next Page

Loading...

w w w . e a t o n . c o m

Installation and User Manual

English

EX

2200 RT 2U

3000 RT 2U

EXB RT 3U

Pulsar Series

86-86710-00 A02 UM.indd 1 14/01/2009 10:56:17

インストレーションおよび

取扱説明書

Installation and User Manual

EX

2200 RT 2U

3000 RT 2U

EXB RT 3U

Pulsar Series

日本語

English

www.eaton.com

Table of Contents

Questions and Answers:

S
Shannon HenrySep 12, 2025
Why is the Eaton UPS load no longer supplied when the rotary switch on the HotSwap MBP module is set to the Bypass position?
- J
  Jessica CarrSep 12, 2025
  If the Eaton UPS load is not supplied when the rotary switch on the HotSwap MBP module is in the Bypass position, the protected devices may be incorrectly wired to the UPS output instead of the HotSwap MBP module. Alternatively, the AC power cord may be connected to the UPS input instead of the HotSwap MBP module. Check the wiring between the UPS and the HotSwap MBP module.
A
ashleywilliamsAug 22, 2025
What to do if Eaton EX 2200 RT 3U indicates LOAD UNPROTECTED OUTPUT OVERLOAD?
- R
  ryanbakerAug 22, 2025
  When your Eaton UPS shows 'LOAD UNPROTECTED OUTPUT OVERLOAD', it signifies that the UPS is overloaded and the connected devices are being fed directly by the electrical network via the By-pass. You should check the power drawn by the connected devices and disconnect any non-priority devices to resolve this.
J
Jessica BurkeAug 25, 2025
What to do if Eaton EX 2200 RT 3U UPS indicates OVERLOAD FAULT REDUCE LOAD?
- T
  Thomas MillerAug 25, 2025
  If your Eaton UPS displays 'OVERLOAD FAULT REDUCE LOAD', it means the UPS shut down automatically due to an overload at the UPS output. To fix this, check the power drawn by the connected devices and disconnect any non-priority devices.
M
milesjenniferAug 27, 2025
What to do if Eaton EX 2200 RT 3U indicates REDUCE LOAD RESTART UPS?
- M
  Martin LeachAug 27, 2025
  If the Eaton UPS displays 'REDUCE LOAD RESTART UPS', it indicates that after repetitive overloads, the UPS is locked in the By-pass position, and the devices are fed directly by the electrical network. You should check the power drawn by the connected devices, disconnect any non-priority devices, then shut down and restart the UPS to return to normal operation.
R
Rachel WaltersAug 28, 2025
What to do if Eaton UPS indicates SITE WIR. FAULT CHECK AC WIRING?
- D
  Daniel WilcoxAug 28, 2025
  If your Eaton UPS displays 'SITE WIR. FAULT CHECK AC WIRING', it indicates a phase inversion on the AC input power, preventing the UPS from starting. Check the polarity and grounding system.
J
Jordan RiveraAug 30, 2025
What to do if Eaton UPS indicates NO BATTERY CHECK CONNECTION?
- M
  matthewstevensonAug 30, 2025
  If your Eaton UPS displays 'NO BATTERY CHECK CONNECTION', it means the battery is incorrectly connected. Check the battery connections.
J
John FosterSep 18, 2025
What to do if Eaton EX 2200 RT 3U load is no longer supplied in Bypass position?
- C
  Charles PhillipsSep 18, 2025
  If the load is not supplied when the rotary switch on the HotSwap MBP module is in the Bypass position, check the wiring between the Eaton UPS and the HotSwap MBP module.
K
Karen JohnsonSep 14, 2025
What to do if the Eaton UPS load is no longer supplied after AC-power fails?
- D
  Dale GraySep 14, 2025
  If the load is not supplied following an AC power failure, ensure the rotary switch on the HotSwap MBP module is in the Normal position. Also, verify the wiring between the Eaton UPS and the HotSwap MBP module.
E
Emily ClarkSep 10, 2025
What to do if Eaton EX 2200 RT 3U load is no longer supplied after AC-power fails?
- V
  vickithompsonSep 12, 2025
  If the Eaton UPS load is no longer supplied after AC power fails, ensure that the rotary switch on the HotSwap MBP module is set to the Normal position. If it is already in the Normal position, check the wiring between the UPS and the HotSwap MBP module.
K
Kimberly WalkerSep 6, 2025
What to do if Eaton EX 2200 RT 3U UPS load is no longer supplied when the rotary switch on the HotSwap MBP module is set to the Normal position?
- D
  Dakota SotoSep 6, 2025
  If the load is no longer supplied when the rotary switch on the HotSwap MBP module is set to the Normal position, it could be because the UPS is shut down or the wiring between the UPS and the HotSwap MBP module is not correct. Start the UPS and check the wiring between the UPS and the HotSwap MBP module.

Eaton EX 2200 RT 3U Specifications

General

Brand	Eaton
Model	EX 2200 RT 3U
Category	UPS
Language	English

Related product manuals

Preview: Eaton EX 2200 RT 2U

Eaton EX 2200 RT 2U

Eaton EX 3000 RT 2U

Preview: Eaton EX RT 5

Preview: Eaton EX RT EXB 5

Eaton EX RT EXB 5

Preview: Eaton EX 700

Eaton EX EXB 1000

Preview: Eaton EX Pulsar Series

Eaton EX Pulsar Series