What to do if Eaton EX 2200 RT 2U indicates OVERLOAD ALARM REDUCE LOAD?
If your Eaton UPS displays 'OVERLOAD ALARM REDUCE LOAD', it means the load level is exceeding the programmed overload level or the UPS capacity. The solution is to reduce the load connected to the UPS.
What to do if Eaton UPS indicates LOAD UNPROTECTED OUTPUT OVERLOAD?
When your Eaton UPS shows 'LOAD UNPROTECTED OUTPUT OVERLOAD', it signifies that the UPS is overloaded and the connected devices are being fed directly by the electrical network via the By-pass. You should check the power drawn by the connected devices and disconnect any non-priority devices to resolve this.
What to do if Eaton EX 2200 RT 2U UPS indicates OVERLOAD FAULT REDUCE LOAD?
If your Eaton UPS displays 'OVERLOAD FAULT REDUCE LOAD', it means the UPS shut down automatically due to an overload at the UPS output. To fix this, check the power drawn by the connected devices and disconnect any non-priority devices.
What to do if Eaton EX 2200 RT 2U UPS indicates REDUCE LOAD RESTART UPS?
If the Eaton UPS displays 'REDUCE LOAD RESTART UPS', it indicates that after repetitive overloads, the UPS is locked in the By-pass position, and the devices are fed directly by the electrical network. You should check the power drawn by the connected devices, disconnect any non-priority devices, then shut down and restart the UPS to return to normal operation.
What to do if Eaton EX 2200 RT 2U UPS indicates SITE WIR. FAULT CHECK AC WIRING?
If your Eaton UPS displays 'SITE WIR. FAULT CHECK AC WIRING', it indicates a phase inversion on the AC input power, preventing the UPS from starting. Check the polarity and grounding system.
What to do if Eaton EX 2200 RT 2U indicates NO BATTERY CHECK CONNECTION?
If your Eaton UPS displays 'NO BATTERY CHECK CONNECTION', it means the battery is incorrectly connected. Check the battery connections.
What to do if Eaton UPS indicates BATTERY FAULT SERV REQUIRED?
If the Eaton UPS displays 'BATTERY FAULT SERV REQUIRED', a fault has been detected on the battery. Replace the battery.
What to do if Eaton UPS LCD indicates REMOTE POWER OFF RPO?
If your Eaton UPS displays 'REMOTE POWER OFF RPO', it means the Remote Power Off (RPO) function has shut down the UPS. Return the contact to the normal position and press the ON/OFF button to restart.
What to do if Eaton UPS load is no longer supplied when the rotary switch on the HotSwap MBP module is set to the Bypass position?
If the load is no longer supplied when the rotary switch on the HotSwap MBP module is set to the Bypass position, it could be due to these reasons: * The protected devices are connected to the UPS output instead of to the HotSwap MBP module. * The AC power cord is connected to the UPS input instead of to the HotSwap MBP module. Check the wiring between the UPS and the HotSwap MBP module.
What to do if Eaton UPS load is no longer supplied when the rotary switch on the HotSwap MBP module is set to the Normal position?
If the load is no longer supplied when the rotary switch on the HotSwap MBP module is set to the Normal position, it could be because the UPS is shut down or the wiring between the UPS and the HotSwap MBP module is not correct. Start the UPS and check the wiring between the UPS and the HotSwap MBP module.
Covers EATON's eco-design, substances, packing, and end-of-life product/battery disposal.
Lists various certification standards the equipment complies with.
Covers electrical hazards, battery handling, safe installation, and environmental precautions.
Notes on handling, installation, and battery charging periods.
Explains symbols for warning, information, action, audible signals, and LED states.
Details dimensions, weight, and part numbers for tower and rack positions.
Identifies and describes connectors and ports on the rear panel of EX 2200/3000/3000 XL and EXB.
Details the buttons, LEDs, and LCD display on the UPS control panel.
Guide on how to unpack the UPS and verify all components are present.
Instructions for setting up the UPS in a vertical tower configuration.
Instructions for mounting the UPS into a standard 19-inch rack.
Explains how to connect RS232/USB ports and install communication cards.
Steps for connecting the UPS to a FlexPDU module for power distribution.
Steps for connecting the UPS to a HotSwap MBP module for maintenance.
How to connect the UPS directly to the power source and loads.
Guide on initial startup, normal operation, and LED indications.
Explains UPS behavior during battery power, low battery, and end of backup time.
Describes how the UPS behaves when AC power is restored.
Instructions on how to safely shut down the UPS.
How to use RPO and ROO functions for remote control.
Overview of the UPS display structure for status, measurements, and personalization.
How to navigate the UPS menu to view measurements like voltage and current.
Steps to personalize UPS settings like language and audio alarm via the control panel.
Details on customizing output voltage, frequency, and overload settings.
Options for start-up behavior, automatic restart, energy saving, and phase inversion.
Settings for battery tests, backup time selection, and discharge protection.
Guide to using the Personal Solution-Pac software for advanced settings.
Table listing indications, diagnostics, and corrections for UPS faults.
Specific troubleshooting steps for UPS units with the HotSwap MBP module.
Safety recommendations and procedures for replacing UPS batteries.
Step-by-step guide to physically remove and install battery modules.
Procedures for performing maintenance on UPS with HotSwap MBP.
Detailed technical data including output power, environment, and electrical specifications.
Guide to configuring programmable outlets using the Personal Solution Pac software.
How to configure shutdown timer for powershare outlets via software.
Definitions of technical terms used in the manual.
To Next Page
General
