Ecoflam Blu 1000 PR/MD User Manual

LB381
13.07.2004
A BRUCIATORI A GAS PROGRESSIVI E MODULANTI
B
MODULATING AND PROGRESSIVE GAS BURNERS
C BRULEURS GAZ PROGRESSIVES ET MODULANTS
D QUEMADOR DE GAS PROGRESIVOS EN MODULANTE
Blu 500 PR / MD
Blu 700 PR / MD
Blu 1000 PR / MD
Blu 1200 PR / MD
Blu 1400 PR / MD
Metano (G20) / G.P.L.(G30-G31)

Ecoflam Blu 1000 PR/MD Specifications

General

Brand	Ecoflam
Model	Blu 1000 PR/MD
Category	Burner
Language	English

Summary

TECHNICAL DATA

Thermal Power and Electrical Specifications

Lists thermal power, voltage, motor, and RPM for models.

BURNER START-UP PROCEDURE

Pre-start checks and ignition sequence

Details safety checks, wiring, and the burner's ignition sequence.

IMPORTANT ADVICE AND ADJUSTMENT

Combustion Adjustment Guidelines

Provides guidance on CO2/CO values and proper combustion tuning.

CONTROL BOX OPERATION

Landis & Staefa LGB22 Timing Sequence

FAULT DISPLAY MESSAGES

Error Codes and Troubleshooting

Lists error messages, flash codes, and their corresponding fault diagnoses.

AIR DAMPER MOTOR ADJUSTMENT

BURNER CAPACITY ADJUSTMENTS

Maximum Capacity Settings

Procedures for adjusting maximum gas and air flow rates.

Minimum Capacity Settings

Procedures for adjusting minimum gas and air flow rates.

Intermediate Capacity Settings

Procedures for setting intermediate gas flow rates.

COMBUSTION AND FIRING HEAD ADJUSTMENT

Firing Head Setting Procedure

Step-by-step guide for adjusting the firing head position.

Electrode Positioning and Nosepiece Removal

PRESSURE SWITCH ADJUSTMENTS

Gas Minimum Pressure Switch Setting

Air Pressure Switch Setting

BURNER IONIZATION CURRENT

Measuring and Setting Ionization Current

CONTROL PANEL COMPONENTS

Blu PR Control Panel Layout

Blu MD Control Panel Layout

RWF 40 MICROPROCESSOR REGULATOR

Display and Key Functions

Describes the RWF 40 regulator's display and the function of each key.

PROGRAMMING LEVEL NAVIGATION

Accessing and Navigating Levels

Flowchart illustrating how to access and navigate through programming levels.

BURNER PARAMETER CONFIGURATION

Changing Set Points

Procedure for modifying the burner's set points.

PID Parameter Tuning

Instructions for setting PID parameters and using the 'tunE' function.

Ignition and Shutoff Differential Settings

Guide for adjusting ignition and shutoff differential parameters (HYS1, HYS3).

INPUT CONFIGURATION

Analog Input and Configuration Codes

DISPLAY ERROR INDICATIONS

Troubleshooting Blinking Display Codes

Explains error codes displayed as blinking numbers and their remedies.

BURNER MAINTENANCE

Annual Maintenance Checklist

Steps for performing regular annual maintenance on the burner.

BURNER TROUBLESHOOTING

Start-Up and Ignition Problems

Guides for diagnosing and resolving start-up and ignition failures.

Operation and Safety Cut-Outs

Troubleshooting steps for burner cut-outs during operation or safety intervals.

BURNER PARAMETERS

Parameter Settings for Probe Types

CONFIGURATION SETTINGS

Configuration Options by Probe Type

BLU 500 PR / MODULAIR P 500 COMPONENTS

BLU 700 PR / MODULAIR P 700 COMPONENTS

BLU 1000 PR / MODULAIR P 1000 COMPONENTS

BLU 1200 PR / MODULAIR P 1200 COMPONENTS

BLU 1400 PR / MODULAIR P 1400 COMPONENTS

Exploded View Diagram

Control Panel Overview

BLU 500 PR PART DESCRIPTIONS

BLU 700 PR PART DESCRIPTIONS

BLU 1000 PR PART DESCRIPTIONS

BLU 1200 PR PART DESCRIPTIONS

BLU 1400 PR PART DESCRIPTIONS

Component List and Part Numbers

Component List and Codes

WIRING DIAGRAMS

Landis SQN31.251A2700 Control Unit Wiring

WIRING DIAGRAM DESCRIPTIONS

Component Wiring Terminals

Control Unit and Probe Connections

LANDIS LGB22.330A27 CONTROL UNIT

Wiring and Operation Settings

LANDIS SQN31.251A2700 MOTORIDUTTORE

Wiring and System Description

WIRING DIAGRAM EXPLANATIONS

Component Function Descriptions