Why is there too little water fill in my EdgeStar DWP62SV Dishwasher?
Too little water fill in your EdgeStar dishwasher may be caused by the dishwasher not being level (level the dishwasher), a defective air breaker (replace the air breaker), or water siphoning out (clean or replace the air breaker).
Why are dishes not cleaned in my EdgeStar DWP62SV Dishwasher?
If your EdgeStar Dishwasher leaves dishes unclean, consider these points: Ensure dishes are loaded properly, following the guidelines. Select a more powerful wash cycle. Use more detergent or switch to a different brand. Rearrange items blocking the spray arms. Lastly, verify that the filter combination at the dishwasher's base is clean and correctly installed.
Why are the dishes still wet after using my EdgeStar DWP62SV Dishwasher?
Several factors can cause dishes to remain wet after a cycle in your EdgeStar Dishwasher. Check if the dishwasher has been loaded improperly, reload it according to instructions. Ensure that there is enough rinse aid. Avoid removing dishes too soon. Note that short cycles may have lower cleaning performance, select a more intensive cycle. Be aware that the dishwasher is not suitable for low-quality coating cutlery.
Why is there cloudiness on glassware after using my EdgeStar DWP62SV Dishwasher?
Cloudiness on glassware from your EdgeStar Dishwasher can result from using too much detergent with soft water; try using less detergent or selecting a shorter wash cycle. Also, the filter may be dusty or blocked, so clean the filter and replace it if needed.
Why does my EdgeStar Dishwasher motor not start?
If the motor in your EdgeStar dishwasher won't start or run, it could be due to defective motor bearings (replace the motor), a defective motor capacitor (replace the motor capacitor), improper motor voltage (replace the motor), or shorted motor windings (replace the motor).
Why does my EdgeStar DWP62SV cycles repeat in error?
If the cycles repeat in error in your EdgeStar dishwasher, the cause may be a defective PCB assembly, which would need to be replaced.
Why does my EdgeStar DWP62SV Dishwasher run with the door open?
If your EdgeStar dishwasher runs with the door open, this may be caused by defective door switch contacts (replace the door switch), a defective door latch (replace the door latch), or a defective PCB assembly (replace the PCB assembly).
Why is my EdgeStar DWP62SV not heating up?
If your EdgeStar dishwasher runs but doesn't heat, it could be due to possible low input voltage (ensure power requirements / power supply in “Specifications” section), a defective temperature sensor (replace it), a defective heating element (replace the heating element), or a defective PCB assembly (replace the PCB assembly).
What causes a stained tub interior in my EdgeStar Dishwasher?
A stained tub interior in your EdgeStar Dishwasher is likely due to detergent containing colorant. Avoid using detergents with colorants.
Why do rust stains appear on cutlery in my EdgeStar Dishwasher?
If you notice rust stains on cutlery after using your EdgeStar Dishwasher, it's because the items aren't non-corrosive. Avoid placing non-dishwasher safe items in the dishwasher.
General| Model Number | DWP62SV |
|---|---|
| Capacity | 6 Place Settings |
| Noise Level | 52 dB |
| Wash Cycles | 6 |
| Control Type | Electronic |
| Color | Silver |
| Voltage | 120V |
| Energy Star Certified | Yes |
| Type | Portable |
| Water Consumption | 3.5 Gallons |
| Wattage | 1200 Watts |
Details precautions for electrical connection, grounding, power supply, and maintenance to prevent shock hazards.
Covers installation, repair, intended use, child supervision, door safety, detergent use, and item placement for safe operation.
Details necessary clearance, water supply, pressure, and temperature specifications for proper dishwasher installation.
Specifies requirements for a grounded outlet, circuit rating, and cautions against using extension cords or removing the ground prong.
Step-by-step guide to connecting the inlet and drain hoses using the provided faucet adapter and quick connect assembly.
Explains the purpose of each button (Power, Program Selector, Delay, Start/Pause) and indicator light on the control panel.
Guides on how to load cups, glasses, bowls, plates, and cutlery for optimal cleaning and to prevent interference with spray arms.
Explains the three parts of the filter system and the process for regular cleaning to ensure optimal performance and prevent clogs.
Addresses common problems like the unit not starting, water not pumping, suds in the tub, and internal stains with solutions.
Outlines what is covered under the one-year parts and 90-day labor warranty, including limitations and exclusions.
Provides instructions on how to contact customer support, the return process, and responsibilities for obtaining warranty service.
To Next Page
