Why is there too little water fill in my EdgeStar Dishwasher?
Too little water fill in your EdgeStar dishwasher may be caused by the dishwasher not being level (level the dishwasher), a defective air breaker (replace the air breaker), or water siphoning out (clean or replace the air breaker).
Why are dishes not cleaned in my EdgeStar DWP62BL Dishwasher?
If your EdgeStar Dishwasher leaves dishes unclean, consider these points: Ensure dishes are loaded properly, following the guidelines. Select a more powerful wash cycle. Use more detergent or switch to a different brand. Rearrange items blocking the spray arms. Lastly, verify that the filter combination at the dishwasher's base is clean and correctly installed.
Why are the dishes still wet after using my EdgeStar DWP62BL?
Several factors can cause dishes to remain wet after a cycle in your EdgeStar Dishwasher. Check if the dishwasher has been loaded improperly, reload it according to instructions. Ensure that there is enough rinse aid. Avoid removing dishes too soon. Note that short cycles may have lower cleaning performance, select a more intensive cycle. Be aware that the dishwasher is not suitable for low-quality coating cutlery.
Why is there cloudiness on glassware after using my EdgeStar DWP62BL?
Cloudiness on glassware from your EdgeStar Dishwasher can result from using too much detergent with soft water; try using less detergent or selecting a shorter wash cycle. Also, the filter may be dusty or blocked, so clean the filter and replace it if needed.
Why does my EdgeStar DWP62BL motor not start?
If the motor in your EdgeStar dishwasher won't start or run, it could be due to defective motor bearings (replace the motor), a defective motor capacitor (replace the motor capacitor), improper motor voltage (replace the motor), or shorted motor windings (replace the motor).
Why does my EdgeStar Dishwasher cycles repeat in error?
If the cycles repeat in error in your EdgeStar dishwasher, the cause may be a defective PCB assembly, which would need to be replaced.
Why does my EdgeStar DWP62BL run with the door open?
If your EdgeStar dishwasher runs with the door open, this may be caused by defective door switch contacts (replace the door switch), a defective door latch (replace the door latch), or a defective PCB assembly (replace the PCB assembly).
Why is my EdgeStar DWP62BL Dishwasher not heating up?
If your EdgeStar dishwasher runs but doesn't heat, it could be due to possible low input voltage (ensure power requirements / power supply in “Specifications” section), a defective temperature sensor (replace it), a defective heating element (replace the heating element), or a defective PCB assembly (replace the PCB assembly).
What causes a stained tub interior in my EdgeStar Dishwasher?
A stained tub interior in your EdgeStar Dishwasher is likely due to detergent containing colorant. Avoid using detergents with colorants.
Why do rust stains appear on cutlery in my EdgeStar Dishwasher?
If you notice rust stains on cutlery after using your EdgeStar Dishwasher, it's because the items aren't non-corrosive. Avoid placing non-dishwasher safe items in the dishwasher.
General| Model Number | DWP62BL |
|---|---|
| Capacity | 6 Place Settings |
| Water Consumption | 3.5 gallons per cycle |
| Wash Cycles | 6 |
| Noise Level | 52 dB |
| Energy Star Rated | No |
| Color | Black |
| Type | Portable |
| Voltage | 120V |
Ensures safe operation by detailing grounding requirements and precautions against electric shock.
Guidelines for safe appliance use, child supervision, and preventing injuries during operation.
Details clearance, water pressure, and temperature specifications for proper installation.
Critical electrical precautions, including grounding, circuit requirements, and cord handling.
Step-by-step guide to connecting the dishwasher to the water faucet using included adapters.
Explanation of buttons, lights, and the display screen on the control panel.
Guidance on arranging dishes, glassware, and cutlery for efficient cleaning and drying.
Detailed guide on how to clean the coarse, main, and fine filters for optimal performance.
Step-by-step instructions for removing and reinstalling the filter system for thorough cleaning.
Explanation of common error codes, their meanings, and potential causes for troubleshooting.
Solutions for problems like the unit not starting or water not being pumped.
Tips for common problems like marks on dishes, cloudiness, and inadequate drying.
To Next Page
