Why is my EdgeStar DWP62SV not heating up?
If your EdgeStar dishwasher runs but doesn't heat, it could be due to possible low input voltage (ensure power requirements / power supply in “Specifications” section), a defective temperature sensor (replace it), a defective heating element (replace the heating element), or a defective PCB assembly (replace the PCB assembly).
Why does my EdgeStar DWP62SV Dishwasher run with the door open?
If your EdgeStar dishwasher runs with the door open, this may be caused by defective door switch contacts (replace the door switch), a defective door latch (replace the door latch), or a defective PCB assembly (replace the PCB assembly).
What to do if my EdgeStar DWP62SV Dishwasher doesn't operate when the Start button is pressed?
If your EdgeStar dishwasher doesn't start when you press the Start button, make sure the door is properly closed. Other potential causes are defective door switch contacts (replace the door switch), a defective door latch (replace the door latch), or a defective PCB assembly (replace the PCB assembly).
What to do if my EdgeStar Dishwasher is leaking water?
If your EdgeStar dishwasher is leaking water, possible causes include too much water fill (replace the air breaker or PCB assembly), a defective drain pump (replace it), the dishwasher not being level (level the dishwasher), loose hose clamps (tighten or replace them), the drain pump assembly not seated properly with the sump (remount it), or a defective door seal (replace it).
How to troubleshoot an EdgeStar DWP62SV that does not start?
If your EdgeStar Dishwasher isn't starting, several factors could be at play. First, check your home's fuse box or circuit breaker; a blown fuse or tripped breaker can cut power to the unit. Replace the fuse or reset the breaker, and consider removing other appliances from the same circuit. Also, ensure the dishwasher is turned on, the door is securely closed and latched, and the power cord is correctly plugged into the wall socket.
What to do if my EdgeStar DWP62SV won't fill with water?
If your EdgeStar dishwasher isn't filling with water, there are several potential causes. First, ensure the water supply is turned on. Other possible causes include a defective water inlet valve (replace it), low water pressure (ensure a minimum of 20 PSI), an obstructed water inlet valve or hose (disassemble and clean), a defective air breaker (replace it), heavy water usage elsewhere in the home (use the dishwasher when water usage is minimal), or a defective PCB assembly (replace it).
How to remove white film on the interior of EdgeStar Dishwasher?
A white film on the interior surface of your EdgeStar Dishwasher is caused by hard water minerals. Wearing rubber gloves, use a damp sponge to clean the interior with dishwasher detergent. Never use any other cleaner.
What causes a stained tub interior in my EdgeStar Dishwasher?
A stained tub interior in your EdgeStar Dishwasher is likely due to detergent containing colorant. Avoid using detergents with colorants.
Why is detergent left in the dispenser cup of my EdgeStar DWP62SV Dishwasher?
Detergent left in the dispenser cup of your EdgeStar Dishwasher is often because dishes are blocking the detergent cups. Re-load the dishwasher according to the manual's instructions.
Why do rust stains appear on cutlery in my EdgeStar Dishwasher?
If you notice rust stains on cutlery after using your EdgeStar Dishwasher, it's because the items aren't non-corrosive. Avoid placing non-dishwasher safe items in the dishwasher.
General| Model Number | DWP62SV |
|---|---|
| Capacity | 6 Place Settings |
| Noise Level | 52 dB |
| Wash Cycles | 6 |
| Control Type | Electronic |
| Color | Silver |
| Voltage | 120V |
| Energy Star Certified | Yes |
| Type | Portable |
| Water Consumption | 3.5 Gallons |
| Wattage | 1200 Watts |
Details precautions for electrical connection, grounding, power supply, and maintenance to prevent shock hazards.
Covers installation, repair, intended use, child supervision, door safety, detergent use, and item placement for safe operation.
Details necessary clearance, water supply, pressure, and temperature specifications for proper dishwasher installation.
Specifies requirements for a grounded outlet, circuit rating, and cautions against using extension cords or removing the ground prong.
Step-by-step guide to connecting the inlet and drain hoses using the provided faucet adapter and quick connect assembly.
Explains the purpose of each button (Power, Program Selector, Delay, Start/Pause) and indicator light on the control panel.
Guides on how to load cups, glasses, bowls, plates, and cutlery for optimal cleaning and to prevent interference with spray arms.
Explains the three parts of the filter system and the process for regular cleaning to ensure optimal performance and prevent clogs.
Addresses common problems like the unit not starting, water not pumping, suds in the tub, and internal stains with solutions.
Outlines what is covered under the one-year parts and 90-day labor warranty, including limitations and exclusions.
Provides instructions on how to contact customer support, the return process, and responsibilities for obtaining warranty service.
To Next Page
