EasyManua.ls Logo

EemaX EMT6 - User Manual

EemaX EMT6
20 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Electric Mini Tank Water Heaters
EMT1 - EMT2.5 - EMT4 - EMT6
Installation and Operating Instruction Manual

Table of Contents

Questions and Answers

  • P
    Peter SanchezAug 8, 2025
    Why EemaX EMT6 Water Heater water does not get hot?
    • M
      Mason AllenAug 8, 2025
      If your EemaX Water Heater isn't heating water, first ensure the power supply is on and working. If the indicator light doesn't illuminate, check that the reset button is pushed in. If the light is on but the water isn't hot, test for a plumbing crossover by shutting off the cold water supply and opening the hot water tap; continuous flow indicates a crossover issue. If there's no crossover, consider replacing the heating element.
  • D
    Daniel AlvarezAug 14, 2025
    Why EemaX Water Heater water is too hot?
    • S
      Sarah ParrishAug 14, 2025
      If the water from your EemaX Water Heater is too hot, try turning the temperature knob counter-clockwise to a lower setting. Allow up to 60 minutes for the temperature to adjust. If the temperature remains high, you may need to replace the thermostat.
  • E
    Edward JohnstonAug 20, 2025
    What to do if EemaX EMT6 is leaking?
    • K
      Kathy LloydAug 20, 2025
      If your EemaX Water Heater is leaking, immediately turn off the power switch and unplug the unit from the outlet. Then, inspect the water fittings and the Temperature & Pressure (T&P) fitting on top of the tank. Finally, remove the cover and check the heating element gasket for any signs of damage.
  • L
    Levi BaileyAug 26, 2025
    Why EemaX EMT6 has odor in water?
    • C
      Christian WoodAug 27, 2025
      Smelly water from your EemaX Water Heater could be due to a reaction between your local water and the heater's anode rod. You should check the anode rod.
  • P
    popejohnSep 1, 2025
    Why EemaX EMT6 Water Heater has brown water?
    • N
      Nicole TownsendSep 1, 2025
      Brown or rusty water from your EemaX Water Heater usually means the anode rod is spent. Replace the anode rod.

Summary

Important Safety Instructions

Technical Data

Dimensions

Schematic Construction

Wiring Diagram

General Information

Technical Description

Installation Instructions

Choose a Location

Select a location for maintenance access, ideally 8-9" from ceiling or walls.

Wall Mounting

Fasten bracket securely, hang heater, confirm piping orientation.

Plumbing Connections

Temperature and Pressure Relief Valve

Closed System Thermal Expansion

Explains thermal expansion and provides recommendations for prevention.

Filling the Water Heater

Using the Supplied Aerator

Explains the purpose and benefit of the .5 GPM aerator for EMT1 model.

Electrical Connections

Instructions for Use

Setting the Thermostat

How to adjust the thermostat for desired temperature and conserve energy.

Setting the Freeze Protection

How to set the thermostat to prevent freezing during extended non-use.

Maintenance Instructions

Descaling the Heating Element

Replacing the Heating Element

Changing the Thermostat

Resetting the High Limit Switch

Trouble Shooting

Water does not get hot

Troubleshooting steps for no hot water.

Water is too hot

Troubleshooting steps for water that is too hot.

Water is not hot enough

Troubleshooting steps for water that is not hot enough.

Water is leaking

Troubleshooting steps for water leaks.

Schematic Disassembly

Parts List

Limited Warranty Information

Exclusions of Coverage from this Limited Warranty

EemaX EMT6 Specifications

General IconGeneral
Power6 kW
Voltage220-240 V
Water Connection1/2 inch
Activation Flow Rate1.6 l/min
MaterialPlastic
Safety FeaturesOverheat Protection

Related product manuals