What to do if EemaX Water Heater has undervoltage?
If your EemaX Water Heater is experiencing undervoltage, it indicates that the inlet voltage is too low compared to the heater's specifications. Provide voltage within specified range.
Why is my EemaX Water Heater producing low heat?
Low heat from your EemaX Water Heater can occur for several reasons: - The outlet temperature is below 90°F/32°C for 5 seconds of flow. - Element failure. - ECO tripped or malfunctioning. - Relay/contactor malfunctioning. - Control board failure. - Inlet water supply out of spec. To attempt a fix, reduce the flow through the unit.
What to do if EemaX FlowCo SPEX35 flow is too high?
If the flow in your EemaX Water Heater is too high, preventing the water from heating to the setpoint temperature, reduce the flow. You can achieve this by using an outlet flow restrictor or a faucet aerator.
What to do if EemaX FlowCo SPEX35 shows freeze warning?
If your EemaX Water Heater displays a freeze warning, it means the inlet temperature is too low (below 35°F). To resolve this, increase the temperature of the inlet water to meet product specifications.
What to do if EemaX FlowCo SPEX35 has overvoltage?
If your EemaX Water Heater is experiencing overvoltage, it means the inlet voltage is too high compared to the heater's specifications. Provide voltage within specified range.
What causes residual heat in EemaX FlowCo SPEX35 Water Heater?
Residual heat in your EemaX Water Heater, indicated by an elevated internal water temperature without flow, is caused by both triacs failing closed. To solve this, run water through the unit.
What to do if EemaX FlowCo SPEX35 Water Heater has inlet thermistor failure?
If your EemaX Water Heater is showing an inlet thermistor failure, this is because the inlet thermistor is interrupted or disconnected. Inspect the connections/wiring of the inlet thermistor.
What to do if EemaX FlowCo SPEX35 Water Heater has outlet thermistor failure?
If your EemaX Water Heater is showing an outlet thermistor failure, this is because the outlet thermistor is interrupted or disconnected. Inspect connections/wiring of outlet thermistor.
What to do if EemaX FlowCo SPEX35 has over-temperature protection?
If the outlet temperature of your EemaX Water Heater exceeds 130°F/54°C, it triggers over-temperature protection. To resolve this, increase the water flow through the unit. This will help decrease the overall temperature rise.
What to do if EemaX FlowCo SPEX35 shows an over-temperature warning?
If the outlet temperature of your EemaX Water Heater exceeds 110°F/38°C, it triggers an over-temperature warning. To address this, increase the flow through the unit. If you desire this temperature, no action is required.
Emphasizes the importance of reading and following all instructions for safe operation to prevent injury or damage.
Describes the FlowCo as a non-thermostatic electric tankless water heater for handwashing and fixed-flow applications.
Details mounting the heater under the sink, specifying clearance and orientation flexibility for optimal installation.
Outlines essential system requirements including minimum/maximum working pressure and optimal operating pressure range.
Provides crucial advice on using specific fittings and avoiding solder to prevent heater damage and warranty voidance.
Lists voltage, max power, max current, and recommended minimum wire size for various heater models.
Details verifying water flow and switching on the breaker, monitoring the InfoCue for proper commissioning.
Provides a table to diagnose issues based on LED patterns, status, causes, heater response, and possible solutions.
Advises periodic cleaning of the faucet aerator or inlet filter screen to maintain consistent water flow.
Lists part numbers for 3/8" compression fittings, including nuts and sleeves for installation.
General| Voltage | 220-240 V |
|---|---|
| Minimum Activation Flow Rate | 1.5 l/min |
| Thermostat | Electronic |
| Water Connection | 1/2" |
| Capacity | Tankless |
| Material | Plastic |
| Power | 35 kW |
To Next Page