What to do if EemaX FlowCo SPEX80 Water Heater has undervoltage?
If your EemaX Water Heater is experiencing undervoltage, it indicates that the inlet voltage is too low compared to the heater's specifications. Provide voltage within specified range.
Why is my EemaX FlowCo SPEX80 producing low heat?
Low heat from your EemaX Water Heater can occur for several reasons: - The outlet temperature is below 90°F/32°C for 5 seconds of flow. - Element failure. - ECO tripped or malfunctioning. - Relay/contactor malfunctioning. - Control board failure. - Inlet water supply out of spec. To attempt a fix, reduce the flow through the unit.
What to do if EemaX Water Heater flow is too high?
If the flow in your EemaX Water Heater is too high, preventing the water from heating to the setpoint temperature, reduce the flow. You can achieve this by using an outlet flow restrictor or a faucet aerator.
What to do if EemaX FlowCo SPEX80 shows freeze warning?
If your EemaX Water Heater displays a freeze warning, it means the inlet temperature is too low (below 35°F). To resolve this, increase the temperature of the inlet water to meet product specifications.
What to do if EemaX FlowCo SPEX80 has overvoltage?
If your EemaX Water Heater is experiencing overvoltage, it means the inlet voltage is too high compared to the heater's specifications. Provide voltage within specified range.
What causes residual heat in EemaX FlowCo SPEX80 Water Heater?
Residual heat in your EemaX Water Heater, indicated by an elevated internal water temperature without flow, is caused by both triacs failing closed. To solve this, run water through the unit.
What to do if EemaX FlowCo SPEX80 has inlet thermistor failure?
If your EemaX Water Heater is showing an inlet thermistor failure, this is because the inlet thermistor is interrupted or disconnected. Inspect the connections/wiring of the inlet thermistor.
What to do if EemaX FlowCo SPEX80 Water Heater has outlet thermistor failure?
If your EemaX Water Heater is showing an outlet thermistor failure, this is because the outlet thermistor is interrupted or disconnected. Inspect connections/wiring of outlet thermistor.
What to do if EemaX FlowCo SPEX80 Water Heater has over-temperature protection?
If the outlet temperature of your EemaX Water Heater exceeds 130°F/54°C, it triggers over-temperature protection. To resolve this, increase the water flow through the unit. This will help decrease the overall temperature rise.
What to do if EemaX FlowCo SPEX80 Water Heater shows an over-temperature warning?
If the outlet temperature of your EemaX Water Heater exceeds 110°F/38°C, it triggers an over-temperature warning. To address this, increase the flow through the unit. If you desire this temperature, no action is required.
Essential guidance for safe installation and operation of the Eemax FlowCo water heater, emphasizing electrical safety.
Overview of the Eemax FlowCo non-thermostatic electric tankless water heater and its intended use for handwashing.
Instructions for securely attaching the Eemax FlowCo heater to a wall, ensuring proper clearance and orientation.
Details on connecting the Eemax FlowCo heater to water supply lines using 3/8" compression fittings.
Guidance on safely connecting the Eemax FlowCo heater to the electrical power supply using appropriate wiring.
Steps to activate and verify the Eemax FlowCo heater after installation, including power-on procedures.
Table detailing the temperature increase capabilities of Eemax FlowCo models based on flow rates.
Temperature rise data for 240VAC heaters when operated at 208VAC, specified by flow rate.
Diagnosing Eemax FlowCo heater issues based on LED status, possible causes, and solutions.
Guidance on routine cleaning of aerators and filter screens to maintain optimal water flow and heater performance.
List of part numbers for compression fittings used with Eemax FlowCo units.
Catalog of replacement parts for various Eemax FlowCo models, including element, control board, and relay.
General| Brand | EemaX |
|---|---|
| Model | FlowCo SPEX80 |
| Category | Water Heater |
| Language | English |
To Next Page