EemaX FlowCo SPEX3512

Questions and Answers

B
Brandon CarterAug 18, 2025
What to do if EemaX FlowCo SPEX3512 Water Heater has undervoltage?
- D
  Daniel WagnerAug 18, 2025
  If your EemaX Water Heater is experiencing undervoltage, it indicates that the inlet voltage is too low compared to the heater's specifications. Provide voltage within specified range.
A
Amy MannAug 20, 2025
Why is my EemaX Water Heater producing low heat?
- P
  Patricia ChenAug 20, 2025
  Low heat from your EemaX Water Heater can occur for several reasons: - The outlet temperature is below 90°F/32°C for 5 seconds of flow. - Element failure. - ECO tripped or malfunctioning. - Relay/contactor malfunctioning. - Control board failure. - Inlet water supply out of spec. To attempt a fix, reduce the flow through the unit.
B
brownmichaelAug 23, 2025
What to do if EemaX FlowCo SPEX3512 flow is too high?
- S
  Shannon SummersAug 23, 2025
  If the flow in your EemaX Water Heater is too high, preventing the water from heating to the setpoint temperature, reduce the flow. You can achieve this by using an outlet flow restrictor or a faucet aerator.
E
Erin BoyleAug 26, 2025
What to do if EemaX FlowCo SPEX3512 Water Heater shows freeze warning?
- L
  Lindsey MeyersAug 26, 2025
  If your EemaX Water Heater displays a freeze warning, it means the inlet temperature is too low (below 35°F). To resolve this, increase the temperature of the inlet water to meet product specifications.
X
xschwartzAug 28, 2025
What to do if EemaX Water Heater has overvoltage?
- A
  Angela GibsonAug 28, 2025
  If your EemaX Water Heater is experiencing overvoltage, it means the inlet voltage is too high compared to the heater's specifications. Provide voltage within specified range.
K
Kathleen JenningsAug 30, 2025
What causes residual heat in EemaX Water Heater?
- D
  Deborah KingAug 30, 2025
  Residual heat in your EemaX Water Heater, indicated by an elevated internal water temperature without flow, is caused by both triacs failing closed. To solve this, run water through the unit.
G
garciahenrySep 1, 2025
What to do if EemaX Water Heater has inlet thermistor failure?
- C
  Casey BradshawSep 2, 2025
  If your EemaX Water Heater is showing an inlet thermistor failure, this is because the inlet thermistor is interrupted or disconnected. Inspect the connections/wiring of the inlet thermistor.
R
Raymond JohnsonSep 4, 2025
What to do if EemaX FlowCo SPEX3512 Water Heater has outlet thermistor failure?
- J
  jennifer40Sep 4, 2025
  If your EemaX Water Heater is showing an outlet thermistor failure, this is because the outlet thermistor is interrupted or disconnected. Inspect connections/wiring of outlet thermistor.
M
Monica JamesSep 7, 2025
What to do if EemaX FlowCo SPEX3512 has over-temperature protection?
- D
  Dustin WhiteSep 7, 2025
  If the outlet temperature of your EemaX Water Heater exceeds 130°F/54°C, it triggers over-temperature protection. To resolve this, increase the water flow through the unit. This will help decrease the overall temperature rise.
M
Matthew MartinezSep 9, 2025
What to do if EemaX FlowCo SPEX3512 Water Heater shows an over-temperature warning?
- B
  Brandon VazquezSep 9, 2025
  If the outlet temperature of your EemaX Water Heater exceeds 110°F/38°C, it triggers an over-temperature warning. To address this, increase the flow through the unit. If you desire this temperature, no action is required.