EINHELL GE-SA 1640 User Manual

GB
- 25 -
8.3 Maintenance
•
A worn out or damaged cutting unit should be
replaced by an authorised expert (see adress
on the warranty certificate).
•
Take care that all fastening elements (screws,
nuts, etc.) are firmly tightened, so that you can
work safely with the scarifier.
•
Store the scarifier in a dry place.
•
For longer life, all screw-fastened parts, such
as wheels and axles should be cleaned and
subsequently oiled.
•
Regular servicing of the scarifier not only
secures longer endurance and performance,
but also contributes to an accurate and simple
scarification of your lawn.
•
At the end of the season, carry out a general
check of the scarifier, and remove all residue
collected. Before the start of every season, it
is absolutely necessary to check the state of
the scarifier. Contact our Customer Service
(see address on the warranty certificate) if
repair work is necessary.
The push bar has a P position (Fig. 15) in order to
take up less space during storage. To adopt this
position you must loosen the quick-release levers
by approx. 3 turns to allow for the higher faste-
ning in the parking position. With the bar in this
position, the scariÞ er can be stood in a corner in
minimum space (Fig. 19). When you return the bar
to the working position, remember to tighten the
quick-release levers again by 3 turns!
8.4 Changing the roller (see Figures 20-23)
Important. Be sure to wear work gloves!
Only replace the roller with a genuine Einhell rol-
ler, as this will ensure top performance and safety
under all conditions.
Remove the two Allen screws (Fig. 20 / Item A).
Lift the roller on this side and pull out in the direc-
tion of the arrow (Fig. 21).
Now slide the new roller in the direction of the ar-
row (Fig. 23) onto the square-ended drive (Fig. 22
/ Item A) and press into the holder (Fig. 23).
Refasten the roller with the two Allen screws (Fig.
20 / Item A).
Apply grease to the square-ended drive from time
to time so that the rollers can be changed easily.
Important. If the blade roller is set unfavorably,
the outer blade (Fig. 21/Item A) may be blocked
by the housing. In this case move the roller half a
turn
8.5 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info
Replacement cutting unit Art. No.: 9060043
Replacement aerating unit, Art. No.: 9060044
9. Disposal and recycling
The equipment is supplied in packaging to pre-
vent it from being damaged in transit. The raw
materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should be
taken to a suitable collection center for proper dis-
posal. If you do not know the whereabouts of such
a collection point, you should ask in your local
council oů ces.
10. Storage
Store the equipment and accessories out of
children’s reach in a dark and dry place at above
freezing temperature. The ideal storage tempera-
ture is between 5 and 30 °C. Store the electric tool
in its original packaging.
Anl_GE_SA_1640_SPK7.indb 25 16.02.2017 09:37:31

EINHELL GE-SA 1640 Specifications

General

Power	1600 W
Product color	Black, Red
Working width	400 mm
Number of claws	30
Number of knives	20
Working depth (max)	12 mm
Rear wheels diameter	175 mm
Front wheels diameter	220 mm
Recommended lawn area	800 m²
Collection box capacity	48 L
Adjustable working depth	Yes
Number of working depth positions	4
AC input voltage	230 V
AC input frequency	50 Hz
Package volume	16000 cm³

Weight and Dimensions

Depth	645 mm
Width	528 mm
Weight	12800 g
Package height	320 mm
Package weight	16000 g