EINHELL GE-SP 3546 RB User Manual

GB
- 17 -
Note:
The pump shaft should measure at least
40 x 40 x 50 cm so that the fl oating switch can
move freely.
5.3 Mains connection
The equipment you have purchased comes with
an earthing-pin plug. The equipment is designed
for connection to a socket outlet with earthing
contact for 230 V ~ 50 Hz. Make sure that the
socket-outlet is suffi ciently fused (at least 6 A)
and in good working order. Insert the power plug
in the socket-outlet and the equipment is ready
for operation.
6. Operation
You can put the equipment into operation after
you have thoroughly read the installation and ope-
rating instructions. Pay attention to the following
points:
•
Make sure that the equipment is set up secu-
rely.
•
Check that the discharge line is fitted correct-
ly.
•
Make sure that the electrical connection is
230 V ~ 50 Hz.
•
Check that the electrical socket-outlet is in
good working order.
•
Make sure that no moisture or water can ever
reach the power connection.
•
Make sure that the equipment does not run
dry.
•
To withdraw water, open the stopcock (Fig. 6,
Item A).
•
To switch off the equipment, pull the power
plug out of the socket outlet.
Setting the ON/OFF switching point:
The ON/OFF switching point can be infi nitely ad-
justed with the height adjustment facility. For this
purpose you must fi rst slacken the screw (Fig. 7,
Point 5). The switching diff erential can be infi nitely
adjusted by extending or shortening the fl oating
cable.
•
The floating switch must be fitted so that the
switching point height: ON and the switch
point height: OFF can be reached easily and
with little force. Check this by placing the
equipment in a container filled with water
and carefully raising and lowering the floating
switch with your hand. You can then see whe-
ther the equipment switches on and off.
•
Make sure that the distance between the floa-
ting switch head and the cable holder is not
too small. If the distance is too small, there
is no guarantee that the equipment will work
correctly.
•
When adjusting the floating switch, make
sure that the floating switch does not touch
the bottom before the equipment is switched
off. Important! Risk of dry running.
Manual operation:
Mount the fl oat switch as illustrated in Figure 8 so
that the device runs continuously. In this mode the
equipment may be used only under supervision
to avoid dry running. The equipment must be swit-
ched off (pull out the power plug) as soon as no
more water is emitted from the discharge line.
7. Replacing the power cable
Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
Danger!
•
Unplug the power plug prior to any mainte-
nance work.
•
For mobile applications, the equipment
should be cleaned with clear water after every
usage.
•
For stationary installation, it is recommended
that you check the floating switch for proper
functioning every three months.
•
Use a water jet to remove any lint or fibrous
particles that may have become trapped in
the housing.
•
Remove sludge from the shaft bottom and
clean the shaft walls every 3 months.
•
Use clear water to remove deposits from the
floating switch.
8.1 Cleaning the fi lter (Figs. 9 to 11)
In order to protect the equipment and the impeller
from severe soiling, an additional fi lter has been
installed in the bottom intake cage. Please pro-
ceed as follows when cleaning the fi lter:
1. Gently press the lateral tab (A) in the direction
of the arrow until the intake cage (4) can be
Anl_GE-SP 3546 RB_SPK1.indb 17Anl_GE-SP 3546 RB_SPK1.indb 17 01.09.2017 13:03:5701.09.2017 13:03:57

EINHELL GE-SP 3546 RB Specifications

General

Brand	EINHELL
Model	GE-SP 3546 RB
Category	Water Pump
Language	English