EINHELL GE-SP 750 LL - User Manual

Questions and Answers

J
Jordan HollandAug 16, 2025
Why does my EINHELL Water Pump switch off after briefly running?
- N
  nicholspaulAug 16, 2025
  Your EINHELL Water Pump might be switching off shortly after starting due to a couple of reasons: * The motor circuit-breaker might be tripping because of excessive water contamination. If this is the case, unplug the power and clean the equipment and shaft. * Alternatively, the water temperature may be too high, causing the motor circuit-breaker to switch off the equipment. Ensure that the water temperature does not exceed 35 °C.
M
Michelle MeltonAug 19, 2025
What to do if my EINHELL GE-SP 750 LL Water Pump switches off after briefly running?
- R
  Rodney CarrollSep 12, 2025
  If your EINHELL Water Pump switches off shortly after starting, it could be due to a couple of reasons. First, the motor circuit-breaker might be activating because of excessive water contamination; in this case, unplug the power and clean the equipment and shaft. Second, the water temperature may be too high, causing the motor circuit-breaker to switch off the equipment. Make sure the water temperature doesn't exceed 35 °C.
J
Jeremy FrederickAug 22, 2025
Why is my EINHELL GE-SP 750 LL not pumping?
- B
  Bryan LopezAug 22, 2025
  If your EINHELL Water Pump isn't pumping water, start by checking the intake sieve. If it's clogged, clean it with a water jet. Also, inspect the discharge hose to ensure it's not kinked. If it is, unkink the hose to allow proper water flow.
J
Joshua RichAug 25, 2025
How to troubleshoot EINHELL Water Pump that does not start?
- A
  Alfred JacksonAug 26, 2025
  If your EINHELL Water Pump isn't starting, begin by checking the power supply to ensure it's properly connected. Also, check the autostart level and ensure it is in the correct position.
L
ldonovanAug 28, 2025
What to do if EINHELL Water Pump has insufficient pumping rate?
- J
  John BlevinsAug 28, 2025
  If your EINHELL Water Pump's pumping rate is insufficient, the intake sieve may be clogged. Clean the intake sieve to resolve this. Additionally, heavily contaminated or abrasive water impurities can reduce performance. In this case, clean the equipment and replace any worn parts.
M
Michelle FisherAug 31, 2025
What to do if EINHELL GE-SP 750 LL Water Pump does not cut out?
- E
  Erik LeeAug 31, 2025
  Turn the autostart level of your EINHELL Water Pump to the correct position.
K
Kyle SawyerSep 2, 2025
What to do if my EINHELL Water Pump does not start?
- F
  Frank HoSep 3, 2025
  If your EINHELL Water Pump doesn't start, there are a couple of things you can check: * First, make sure the power supply is properly connected. * Second, check the floating switch. If it's not triggering, raise its position.
J
Jennifer HudsonSep 6, 2025
What to do if my EINHELL Water Pump does not pump water?
- B
  benjaminbrownSep 6, 2025
  If your EINHELL Water Pump isn't pumping water, it could be due to a couple of issues: * The intake sieve might be clogged. If so, clean it with a water jet. * The discharge hose could be kinked. Straighten the hose to remove any kinks.
P
Paula VegaSep 9, 2025
Why EINHELL GE-SP 750 LL Water Pump has insufficient pumping rate?
- W
  William YoungSep 9, 2025
  An insufficient pumping rate in your EINHELL Water Pump can occur due to: * A clogged intake sieve. Clean the intake sieve. * Reduced performance caused by heavily contaminated and abrasive water impurities. Clean the equipment and replace any worn parts.
A
allenrobertSep 12, 2025
What to do if my EINHELL Water Pump does not cut out?
- D
  David OnealSep 12, 2025
  If your EINHELL Water Pump isn't cutting out, it might be because the floating switch can't sink. Ensure the equipment is correctly placed on the shaft bottom.

EINHELL GE-SP 750 LL Specifications

General

Power	750 W
Max Immersion Depth	7 m
Max Water Temperature	35 °C
Max Size of Foreign Particles	5 mm
Pump Housing	Plastic
Mains Supply	230 V
Voltage	230 V
Frequency	50 Hz
Cable Length	10 m
Suction Connection	1
Inlet/Outlet Diameter	1 inch