EINHELL TC-CS 1410 User Manual

GB
- 27 -
Danger!
When using the equipment, a few safety pre-
cautions must be observed to avoid injuries and
damage. Please read the complete operating
instructions and safety regulations with due care.
Keep this manual in a safe place, so that the in-
formation is available at all times. If you give the
equipment to any other person, hand over these
operating instructions and safety regulations as
well. We cannot accept any liability for damage
or accidents which arise due to a failure to follow
these instructions and the safety instructions.
1. Safety regulations
Warning!
Read all the safety information, instructions,
illustrations and technical data provided on
or with this power tool. Failure to adhere to the
following instructions may result in electric shock,
re and/or serious injury.
Keep all the safety information and instruc-
tions in a safe place for future use.
General safety information for power tools
The term „power tool“ used in the safety informati-
on and instructions refers to power tools operated
from the mains power supply (with a power cable)
and to battery operated power tools (without a
power cable).
1. Workplace safety
a) Keep your work area clean and well lit.
Untidy or unlit work areas can result in acci-
dents.
b) Do not use this power tool in an area
where there is a risk of explosion and
where there are inammable liquids,
gases or dust. Power tools generate sparks
that can ignite dust or vapors.
c) Keep children and other people away
from the power tool while you are using
it. If you are distracted you may lose control
of the power tool.
2. Electrical safety
a) The plug on the power tool must t into
the socket. The socket must not be modi-
ed in any way. Do not use adapter plugs
together with power tools with a protecti-
ve earth. Unmodied plugs and matching so-
ckets will reduce the risk of an electric shock.
b) Avoid body contact with earthed surfaces
such as pipes, heating systems, stoves
and refrigerators. There is an increased risk
of suering an electric shock if your body is
earthed.
c) Keep the power tool out of the rain and
away from moisture. The ingress of water
into an electric power tool increases the risk
of an electric shock.
d) Do not use the power cable for a purpose
for which it is not designed, for example
to carry the power tool, hang it up or to
pull the plug out of the socket. Keep the
power cable away from heat, oil, sharp
edges and moving parts. Power cables that
are damaged or tangled increase the risk of
an electric shock.
e) If you use an electric power tool out-
doors, use only extension cables that are
suitable for outdoor use. The use of an
extension cable which is suitable for outdoor
use reduces the risk of an electric shock.
f) If you cannot avoid using the power tool
in a damp location, use a residual current
device (RCD) circuit breaker. The use of a
residual current device (RCD) circuit breaker
will reduce the risk of suering an electric
shock.
3. Safety of persons
a) Be careful, watch what you are doing and
be sensible and responsible when using
an electric power tool. Never use the po-
wer tool if you are tired or under the inu-
ence of drugs, alcohol or medication. One
moment of inattention when using the electric
tool can result in serious injuries.
b) Wear personal safety equipment and
always wear safety goggles. Wearing per-
sonal safety equipment such as dust masks,
non-slip safety shoes, a helmet or ear plugs,
depending on the type and application of the
tool, reduces the risk of injury.
c) Make sure that the tool cannot start up
accidentally. Ensure that the power tool is
switched o before you connect it to the
power supply and/or connect the battery
pack, pick it up or carry it. If you have your
nger on the switch while carrying the power
tool or if you connect the power tool to the
power supply while it is switched on, this may
cause accidents.
d) Remove all adjusting tools or wrenches
before you switch on the power tool. Any
tool or wrench in a rotating part of the power
Anl_SA_TC_CS_1410_SPK8.indb 27Anl_SA_TC_CS_1410_SPK8.indb 27 02.12.2021 15:27:0802.12.2021 15:27:08

EINHELL TC-CS 1410 Specifications

General

Dust blower	Yes
Product color	Red
Built-in light	No
Suitable for materials	Wood
Blade diameter	190 mm
Number of teeth	24
Idle speed (max)	5500 RPM
Cutting depth (45º)	46 mm
Cutting depth (90º)	67 mm
Input power	1410 W
Power source	AC
AC input voltage	220 - 240 V
AC input frequency	50 - 60 Hz

Weight and Dimensions

Weight	4330 g
Package depth	270 mm
Package width	360 mm
Package height	290 mm
Package weight	5450 g