EINHELL TC-TS 2025/1 U User Manual

GB
- 39 -
alcohol or medication. A moment of inatten-
tion when using the electric tool can result in
serious injuries.
•
Do not use an electric tool with a defective
switch. An electric tool that cannot be swit-
ched on or off is dangerous and must be
repaired.
•
Keep unused electric tools out of the reach of
children. Do not allow people who are not fa-
miliar with the tool or who have not read these
instructions to use the tool. Electric tools are
dangerous if they are used by inexperienced
people.
•
Keep your cutting tools sharp and clean.
Carefully maintained cutting tools with sharp
cutting edges will jam less and are easier to
control.
•
If the connection lead on the electric tool is
damaged, it must be replaced by a specially
prepared connection lead available from our
customer service organization.
•
Have your tool repaired only by trained per-
sonnel using only genuine spare parts. This
will ensure that you tool maintains its safety
standard.
•
The machine has to be set up where it can
stand securely.
•
All covers and safety devices have to be pro-
perly fitted before the machine is switched on.
•
It must be possible for the blade to run freely.
•
When working with wood that has been pro-
cessed before, watch out for foreign bodies
such as nails or screws etc.
•
Before you actuate the On/Off switch, make
sure that the saw blade is correctly fitted and
that the machine’s moving parts run smoothly.
•
Follow the instructions for lubrication and
changing tools.
•
Keep handles dry, clean and free from oil and
grease.
•
Keep the push stick or handle for a push
block at the machine at all times, even when
you are not using them.
•
Use only the transport device for transporting
the machine.
•
While you are moving the machine it is best
to cover the top part of the blade, for example
using a guard.
Do not lose these safety instructions.
2. Layout and items supplied
2.1 Layout (Fig. 1-3, 7-8, 11-14)
1. Sawing table
2 Saw blade guard
3 Push stick
4 Saw blade
5 Splitter
6 Table insert
7 Parallel stop
8 Hand wheel
9 Adjusting and locking grip
10 Base frame
11 On/Off switch
12 Eccentric lever
13 Rubber foot
14 Cross stop
15 Screw
16 Extractor adapter
17 Countersunk head screw
18 Hole (splitter)
19 Fastening screw
20 Screw
21 Groove
22 Scale
23 Stop rail
24 Holder
25 Slot
26 Screw
27 Slot
28 Guide rail
29 Leg (A)
30 Cross strut (B)
31 Longitudinal strut (C)
32 Support
33 Table width extension
34 Tool hook
35 Extractor hose
36 Additional leg
37 Ring wrench 10/13 mm
38 Ring wrench 10/21 mm
a Hex screw
b Nut
c Round-head screw
2.2 Items supplied
Please check that the article is complete as
specifi ed in the scope of delivery. If parts are
missing, please contact our service center or the
sales outlet where you made bought the product
within the maximum days indicated by the con-
sumer protection laws of your country and upon
presentation of a valid bill of purchase. Also, refer
Anl_SA_TC_TS_2025_1_U_SPK8.indb 39Anl_SA_TC_TS_2025_1_U_SPK8.indb 39 23.05.2019 08:34:3923.05.2019 08:34:39

EINHELL TC-TS 2025/1 U Specifications

General

Input power	2000 W
AC input voltage	220-240 V
AC input frequency	50 Hz
Number of teeth	24
Idle speed (max)	5000 RPM
Cutting depth (45º)	65 mm
Cutting depth (90º)	85 mm

Weight and Dimensions

Depth	719 mm
Width	559 mm
Height	333 mm
Weight	18800 g
Package weight	22500 g
Base plate depth	487 mm
Base plate width	640 mm
Height adjustment range	0 - 85 mm