O
osmithAug 20, 2025
How to adjust brightness on Eizo monitor?
- MMichael NguyenAug 20, 2025
If your Eizo monitor screen is too bright or too dark, adjust the brightness or contrast settings using the [Brightness] or [Contrast] controls.
To Next PageTo Next PageHow to adjust brightness on Eizo monitor?
If your Eizo monitor screen is too bright or too dark, adjust the brightness or contrast settings using the [Brightness] or [Contrast] controls.
What to do if my Eizo FLEXSCAN S2433W has no picture and the power indicator light is orange?
If your Eizo monitor displays no picture but the power indicator is orange, ensure that your PC is turned on. Also, try switching the input signal using the designated button on your monitor. Another option is to operate the mouse or keyboard.
Why does my Eizo FLEXSCAN S2433W say the input signal is out of range?
If your Eizo monitor displays a message indicating that the input signal is out of the specified frequency range, verify that your PC's signal settings match the monitor's resolution and vertical frequency settings. If needed, reboot your PC. Alternatively, use your graphics board’s utility to select an appropriate display mode.
Why is my Eizo FLEXSCAN S2433W Monitor connected with the USB cable not detected?
If your Eizo monitor is not detected when connected with a USB cable, first, check if the USB cable is correctly connected. If it is, try changing the USB port to another one. Rebooting your PC may also resolve the issue. Ensure that your PC and operating system are USB compliant, and check your PC’s BIOS settings for USB when using Windows.
What to do if my Eizo Monitor has no picture and the power indicator does not light?
If your Eizo monitor displays no picture and the power indicator does not light up, check whether the power cord is connected correctly. If the problem persists, turn off the main power, and then turn it on again after a few minutes. Ensure that the main power switch is turned on, and press the power button.
What to do if my Eizo Monitor has no picture and the power indicator light is blue?
If your Eizo monitor displays no picture but the power indicator light is blue, set each adjusting value in [Brightness], [Contrast] and [Gain] to a higher level. When using a long DVI cable, adjust the DVI input level using the [DVI Input Level] setting.
Why does noise appear on the screen of my Eizo FLEXSCAN S2433W Monitor?
If you are experiencing noise on the screen of your Eizo monitor, and you are using analog input signals, access the menu and change the setting to 'On'. Also, note that when using HDCP system signals, normal images might not display immediately. If you're using a long DVI cable, try adjusting the DVI input level using the [DVI Input Level] setting.
What to do if a message appears on my Eizo FLEXSCAN S2433W Monitor?
If your Eizo monitor displays a message, first, check whether the PC is turned on. Then, check whether the signal cable is connected properly. You can also try switching the input signal. If you're using a long DVI cable, adjust the DVI input level using [DVI Input Level].
How to fix no audio output on Eizo FLEXSCAN S2433W Monitor?
If your Eizo monitor has no audio output, check whether the mini jack cable is correctly connected and ensure that the volume is not set to 0. Verify the settings of your PC and the audio playback software. If you are using DisplayPort signal input, check the [Source] setting.
Why do afterimages appear on my Eizo monitor?
If your Eizo monitor displays afterimages, use a screen saver or the off timer function for long-time image displays. Avoid displaying the same image for extended periods.
General| Pixel pitch | 0.270 x 0.270 mm |
|---|---|
| Aspect ratio | 16:10 |
| Response time | 6 ms |
| Display diagonal | 24.1 \ |
| Display resolution | 1920 x 1200 pixels |
| Vertical scan range | 55 - 76 Hz |
| Horizontal scan range | 31 - 94 kHz |
| Viewable size diagonal | 611 mm |
| Contrast ratio (typical) | 1000:1 |
| Display number of colors | 16.78 million colors |
| Digital vertical frequency | 59 - 61 Hz |
| Digital horizontal frequency | 31 - 76 kHz |
| Display brightness (typical) | 360 cd/m² |
| Display viewable area (HxV) | 518.4 x 324 mm |
| HDCP | Yes |
| I/O ports | DisplayPort |
| USB hub version | 2.0 |
| Headphone connectivity | 3.5 mm |
| USB Type-A downstream ports quantity | 3 |
| RMS rated power | 1 W |
| Certification | TCO Displays 5.0, EPEAT Gold, TÜV/Ergonomics ( ISO 13406-2), TÜV/GS, c-Tick, CE, CB, UL (cTÜVus), CSA (cTÜVus), FCC-B, Canadian ICES-003-B, TÜV/S, VCCI-B, EPA Energy Star, RoHS, WEEE, EIZO Eco Products 2009 |
| Product color | Black |
| Market positioning | - |
| Compliance industry standards | VESA DDC 2B |
| Power consumption (typical) | 95 W |
| Power consumption (PowerSave) | 1.5 W |
| Sustainability certificates | ENERGY STAR |
Weight and Dimensions| Depth (with stand) | 208.5 mm |
|---|---|
| Height (with stand) | 538 mm |
| Weight (with stand) | 10200 g |
| Depth (without stand) | 85 mm |
| Width (without stand) | 566 mm |
| Height (without stand) | 367 mm |
| Weight (without stand) | 7200 g |
Lists key features like 24" WUXGA display, built-in speakers, and power saving.
Details the monitor's buttons, sensors, and connectors for operation.
Covers automatic and manual adjustments for screen position, size, and clarity.
Explains how to select display modes and perform advanced color adjustments like brightness and contrast.
Provides causes and remedies for issues where the monitor displays no picture or has indicator light problems.
Addresses messages like "Signal Check" or "Signal Error" indicating input signal problems.
