Why is there higher wire wear out at the wire-feeding unit of my Elektron Welding System?
If you notice a higher wire wear out at the wire-feeding unit of your Elektron Welding System, it could be because the wire rolls do not fit the wire diameter. Install the right wire rolls. Another reason might be wrong contact pressure at wire feeding; adjust as described in the manual.
What to do if the DP20 operating panel is completely dark on my Elektron Welding System?
If the DP20 operating panel on your Elektron Welding System is completely dark, it could be due to a missing phase. Try checking the unit at another power outlet and inspect the power cable, mains fuses, and circuit breakers.
Why is the welding performance less than expected on my Elektron Welding System?
If you're experiencing less welding performance with your Elektron Welding System, there might be a phase missing. Check the unit at another power outlet, inspect the power cable and mains fuses/circuit breakers. Also, ensure the best possible contact between the ground clamp and workpiece. Fasten the ground cable by turning the plug to the right. A defect torch can also be the reason, so repair or replace it.
Why does my Elektron Welding System unit keep switching off?
If your Elektron Welding System unit switches off, it could be due to an overloaded duty cycle. Allow the machine to cool down. Another reason might be insufficient cooling of unit parts, so check the air inlet and outlet.
What causes no shielded gas in my Elektron Welding System?
If you're not getting any shielded gas with your Elektron Welding System, it could be because the gas cylinder is empty. Replace it. Another reason could be a defect torch; check and replace if necessary. The pressure reducer might be dirty or defective, so check and replace it as well. Also, the valve of the gas cylinder could be defective; in that case, replace the gas cylinder.
How to fix a torch that is too hot on my Elektron Welding System?
If the torch is too hot on your Elektron Welding System, it could be due to insufficient coolant flow because of pollution in the coolant. Swill the waterhoses of the torch in the opposite direction. Also, check if the contact tip is tight.
What to do if the Elektron Welding System has irregular wire feeding or wire welds to the contact tip?
If you're experiencing irregular wire feeding or the wire welds to the contact tip on your Elektron Welding System, the wire electrode might be tight at the spool. Check and change it if necessary. Also, there might be a burr at the wire beginning, so cut the wire beginning again.
What causes the shielded gas to not switch off on my Elektron Welding System?
If the shielded gas on your Elektron Welding System is not switching off, it could be because the valve of the gas cylinder is dirty or does not close. Remove the torch and pressure reducer and clean it with compressed air.
Why is there not sufficient shielded gas in my Elektron Welding System?
If you're experiencing insufficient shielded gas with your Elektron Welding System, it could be due to a wrongly adjusted quantity of shielded gas. Adjust it correctly as described in the manual. A dirty pressure reducer could also be the cause, so check the valve. Additionally, the torch or gashose might be blocked or not airtight; check and change if necessary. Finally, the shielded gas might be blown away by draught; avoid draught.
Why is the ground cable plug hot on my Elektron Welding System?
If you experience a hot plug of the ground cable on your Elektron Welding System, it may be because the plug was not tightened by turning it to the right. Check it.
Step-by-step guide for physically connecting the welding torch to the machine.
Instructions for connecting the welding machine to the power supply socket.
Guide on how to correctly mount and prepare the wire spool for feeding.
Instructions for connecting the ground cable to the workpiece or welding bench.
Guide on programming, saving, and managing welding jobs using the Tiptronic function.
Instructions for selecting, activating, deactivating, reprogramming, and copying welding jobs.
Guide on operating the machine independently of pre-set characteristics, setting voltage and speed.
General| Input Voltage | 3 x 400 V |
|---|---|
| Duty Cycle | 60% at 400A |
| Weight | 65 kg |
| Dimensions | 950 x 520 x 780 mm |
| Protection Class | IP21S |
| Power Supply | 3-phase |
| Welding Method | MIG/MAG |
To Next Page
