GB
34
WARNING
Before carrying out unloading operations, always -
ensure that there are no people, animals or objects in
the vicinity of the trailer.
During work always bear in mind that the wheel track of -
the trailer is wider than that of the machine by 12 cm, 6
on each side. Dimensions: 112x85x28 cm.
Spreader
After having loaded the hopper with the material to be spread
on the ground, use the graduated lever to adjust the width of
the outfeed to suit your requirements. The accessory is
equipped with a sieve, to retain larger clumps of material that
you do not want deposited on the ground, and a plastic cover,
which can be used for example when spreading rock salt
during rainy or snowy weather, or to cover powdered materials.
Maintenance
- Before or after a long period of storage, use automotive oil
to lubricate the retaining hook on the tipper body, the locking
pin on the retaining hook and the part of the frame with the
two holes for fixing the machine’s towing hitch and
corresponding pin.
Periodically grease or oil the wheel bearings. Use grease for -
wheel bearings or automotive oil.
Periodically check the tightness of all screws, nuts and -
bolts.
Always keep the tyres sufficiently inflated. Never exceed the -
maximum recommended pressure. Incorrectly inflated tyres
(for example inflated to different pressures) may cause loss
of balance.
3) Stone-guard kit
For use in place of the grass-catcher, when the cuttings are
not to be collected.
After having removed the grass-catcher, fit the stone-guard
using the two pins (D, Fig.13) and cotter pins (E).
Key to functional wiring diagram (Fig.25)
Q0 = ignition key switch:
- pos.OFF =
machine off
- pos.R = machine in reverse with mowing
- pos.1 = machine forward with mowing
- pos.ON =
on
Q1 = electric brake control switch
Q1.1 = 1.2 W blade engaged indicator lamp
H1 = grass-catcher full indicator lamp
S1 = machine stopped micro-switch (NC)
S2 = grass-catcher opening micro-switch (NO)
S3 = seat micro-switch (NO)
S4 = parking brake micro-switch (NO)
S6 = grass-catcher full micro-switch (NO)
S7 = machine stopped and reverse gear micro-switch (NO)
S.E. = electronic circuit board
CH = grass-catcher full buzzer
F1 = machine power supply fuse
F2 = electric brake fuse
XS1 = circuit board power supply connector
XS2 = buzzer connector
K1M = power supply and switch-off relay
K2M = starting command relay
K3M = starting relay
M.Avv. = starter motor
MCI = internal combustion engine
EF = 1.7 A electromagnetic brake
Cable colour coding
A = light blue G = yellow M = brown S = pink
B = white H = grey N = black V = green
C = orange L = blue R = red Z = purple
Electrical system 12 V
Battery 17 Ah
Front tyres 11” x 4”-4
Rear tyres 15” x 6”-6
Front tyre pressure 1,5 bar
Rear tyre pressure 1,0 bar
Overall dry weight 170 kg
Inside turning circle 0,9 m
Cutting height 3÷8 cm
Cutting width 72 cm
Grass-catcher capacity 180 litres
Ground speed (at 3000 min
-1
):
- in forward drive 0÷8,6 km/h
- in reverse drive 0÷3,2 km/h
Sound pressure level (LpA EN 836/A2) 90,5 dB (A)
Uncertainty 2,0 dB (A)
Measured sound power level
(LwA 2000/14/EC - EN ISO 3744 - ISO 11094)
98,8 dB (A)
Uncertainty 1,2 dB (A)
Guaranteed sound power level
(LwA 2000/14/EC - EN ISO 3744 - ISO 11094)
100,0 dB (A)
Vibration level (EN 836/A2) steering wheel
3,0(sx)-3,4(dx) m/s
2
Uncertainty (EN 12096) 1,1 m/s
2
Vibration level (EN 836/A2) seat 0,47 m/s
2
Uncertainty (EN 12096) 0,23 m/s
2
Overall dimensions 198x73x110 cm
10. TECHNICAL DATA
To Next Page
Loading...
