Emerson Rosemount 3051SAL - C.3 Installation considerations; C.4 Transient; lightning considerations

137
Reference Manual
00809-0200-4802, Rev BA
Appendix A: Specifications and reference data
May 2013
Specifications and Reference Data
Special Cleaning
Expanded
P2 Cleaning for special services
P3 Cleaning for less than 1PPM chlorine/fluorine
Calibration Certification
Standard Standard
Q4 Calibration certificate ★
QP Calibration certificate and tamper evident seal ★
Material Traceability Certification
Standard Standard
Q8 Material traceability certification per EN 10204 3.1 ★
Quality Certification for Safety
Standard Standard
QS
(11)
Prior-use certificate of FMEDA data ★
QT
(21)
Safety certified to IEC 61508 with certificate of FMEDA data ★
Transient Protection
Standard Standard
T1
(22)(23)
Transient terminal block ★
Toolkit Total System Performance Reports
Standard Standard
QZ Remote Seal System Performance Calculation Report ★
Conduit Electrical Connector
Standard Standard
GE
(24)
M12, 4-pin, Male Connector (eurofast
®
) ★
GM
(24)
A size Mini, 4-pin, Male Connector (minifast
®
) ★
Typical Model Number for EF seal:
3051S2LD2AA1A1020DEF71DA20
(1) Requires PlantWeb housing.
(2) Available approvals are FM Intrinsically Safe, Division 2 (option code I5), CSA Intrinsically Safe (option code I6), ATEX Intrinsic Safety
(option code I1), and IECEx Intrinsic Safety (option code I7).
(3) Available with output code A only. Available approvals are FM Intrinsically Safe, Division 2 (option code I5), ATEX Intrinsic Safety (option code I1), or IECEx Intrinsic Safety
(option code I7). Contact an Emerson Process Management representative for additional information.
(4) With option code 1, user must select Seal Location option code M in Table 6 of Rosemount DP Level PDS.
(5) Not recommended for use with spiral wound metallic gaskets (see 1199 product data sheet, document 00813-0100-4016 for additional options).
(6) Standard gasket for lower housing consists of non-asbestos fiber.
(7) Long-life Power Module must be shipped separately, order Part No. 00753-9220-0001.
(8) Materials of Construction comply with metallurgical requirements highlighted within NACE MR0175/ISO 15156 for sour oil field production environments. Environmental
limits apply to certain materials. Consult latest standard for details. Selected materials also conform to NACE MR0103 for sour refining environments.
(9) Requires PlantWeb housing and output code A. Includes Hardware Adjustments as standard.
(10) Consult an Emerson Process Management representative for availability.
(11) Not available with output code F.
(12) Not available with housing style codes 00, 2E, 2F, 2G, 2M, 5A, 5J, or 7J.
(13) Requires PlantWeb housing and Hardware Adjustments option code D1. Limited availability depending on transmitter type and range. Contact an Emerson Process
Management representative for additional information.
(14) Transmitter is shipped with 316 SST conduit plug (uninstalled) in place of standard carbon steel conduit plug.
(15) Valid when SuperModule Platform and housing have equivalent approvals.
(16) Not available with M20 or G ½ conduit entry size.
(17) Only available on differential and gage measurement types. Silicone fill fluid is standard.
(18) Not available with Housing 7J.
(19) Not available with output code F, option code DA1, option code DA2, or option code QT.
(20) See the 3051S Reference Manual (document number 00809-0100-4801) for cable requirements. Contact an Emerson Process Management representative for additional
information.