Emerson Rosemount 644 with HART Protocol User Manual

Name: Emerson Rosemount 644 with HART Protocol
Brand: Emerson
Rating: 5 (1 reviews)

112 pages

To Next Page

To Previous Page

Table of Contents3
Using this Manual9
- Transmitter Overview10
Overview11
Safety Messages12
System Readiness12
- Confirm Correct Device Driver13
- Surges/Transients13
Configuration Methods13
- Configuring on the Bench13
- Selecting a Configuration Tool14
- Setting the Loop to Manual16
- Failure Mode16
- HART Software Lock17
Verify Configuration17
- Field Communicator17
- AMS Device Manager18
- Loi18
- Checking Transmitter Output18
Basic Configuration of the Transmitter19
- Mapping the HART Variables20
- Configuring the Sensor(S)21
- Setting Output Units22
Configure Dual Sensor Options23
- Differential Temperature Configuration24
- Average Temperature Configuration25
- Hot Backup Configuration26
- Sensor Drift Alert Configuration28
Configure Device Outputs29
- Re-Range the Transmitter29
- Damping30
- Configure Alarm and Saturation Levels32
- Configuring the LCD Display33
Inputting Device Information35
- Tag, Date, Descriptor and Message35
Configure Measurement Filtering36
- 50/60 Hz Filter36
- Resetting the Device37
- Intermittent Sensor Detection37
- Open Sensor Hold off38
Diagnostics and Service39
- Performing a Loop Test39
- Simulate Digital Signal (Digital Loop Test)39
- Thermocouple Degradation Diagnostic40
- Minimum/Maximum Tracking Diagnostic42
Establishing Multi Drop Communication43
- Changing a Transmitter Address43
Using the Transmitter with the HART Tri-Loop44
- Set the Transmitter to Burst Mode44
- Set Process Variable Output Order45
Transmitter Security46
- Available Security Options46
Overview49
Safety Messages50
Considerations50
- General50
- Commissioning50
- Installation50
- Mechanical51
- Electrical51
- Environmental51
Installation Procedures52
- Set the Alarm Switch53
- Mount the Transmitter54
- Install the Device55
- Multichannel Installations59
- LCD Display Installation60
- Rev SA July62
Overview63
Safety Messages63
Wiring and Powering the Transmitter63
- Sensor Connections64
- Power the Transmitter66
- Ground the Transmitter67
- Wiring with a Rosemount 333 HART Tri-Loop (HART/4-20 Ma Only)70
Overview73
Safety Messages73
Calibration Overview74
- Trimming74
Sensor Input Trim74
- Application: Linear Offset (Single-Point Trim Solution)75
- Application: Linear Offset and Slope Correction (Two-Point Trim)75
- Recall Factory Trim-Sensor Trim76
- Active Calibrator and EMF Compensation77
Trim the Analog Output77
- Analog Output Trim or Scaled Analog Output Trim77
- Analog Output Trim78
- Performing a Scaled Output Trim79
Transmitter-Sensor Matching79
Switching HART Revision81
- Generic Menu81
- Field Communicator81
- AMS Device Manager81
- Loi82
Overview83
Safety Messages83
4-20 Ma/Hart Output84
Diagnostic Messages85
- Failed Status85
- Warning Status86
- Other LCD Display Messages88
Return of Materials88
SIS Certification89
Safety Certified Identification89
Installation90
- Damping90
- Alarm and Saturation Levels90
- SIS Certification90
Operation and Maintenance91
- Proof Test91
- Partial Proof Test 191
- Comprehensive Proof Test 292
- Comprehensive Proof Test 392
- Inspection93
Specifications93
- Failure Rate Data93
- Failure Values93
- Product Life93
A.1 Product Certifications95
Ordering Information, Specifications, and Drawings95
Field Communicator Menu Trees97
Field Communicator Fast Keys103
C.1 Number Entry105
Number Entry105
Text Entry106
- Scrolling106
- C.2 Text Entry106
C.3 Timeout108
Timeout108
Saving and Canceling108
LOI Menu Tree109
LOI Menu Tree - Extended Menu110

Emerson Rosemount 644 with HART Protocol User Manual

Table of Contents

Questions and Answers:

Emerson Rosemount 644 with HART Protocol Specifications

Related product manuals

Brand	Emerson
Model	Rosemount 644 with HART Protocol
Category	Transmitter
Language	English