Emerson Unidrive M100 - Menu 7: Analog I;O

Safety
information
Product
information
Mechanical
installation
Electrical
installation
Getting
started
Basic
parameters
Running the
motor
Optimization NV Media Card
Advanced
parameters
Diagnostics UL Listing
68 Unidrive M100 / M101 Control User Guide
Issue Number: 1
10.8 Menu 7: Analog I/O
Figure 10-8 Menu 7 logic diagram
Parameter
Range
(Ú) Default(Ö)
Type
OL OL
07.001 Analog Input 1 (T2) ±100.00 %
RO Num ND NC PT FI
07.004 Stack Temperature ±250 °C
RO Num ND NC PT
07.005 Auxiliary Temperature ±250 °C
RO Num ND NC PT
07.007 Analog Input 1 Mode (T2)
4-20.S (-6), 20-4.S (-5),
4-20.L (-4), 20-4.L (-3),
4-20.H (-2), 20-4.H (-1), 0-20 (0),
20-0 (1), 4-20.tr (2), 20-4.tr (3),
4-20 (4), 20-4 (5), VoLt (6)
VoLt (6) RW Txt US
07.008 Analog Input 1 Scaling (T2) 0.000 to 10.000 1.000 RW Num US
07.009 Analog Input 1 Invert (T2) Off (0) or On (1) Off (0) RW Bit US
07.010 Analog Input 1 Destination A (T2) 0.000 to 30.999 1.036 RW Num DE PT US
07.026 Analog Input 1 Preset on Current Loss (T2) 4.00 to 20.00 4.00 RW Num US
07.028 Analog Input 1 Current Loop Loss (T2) Off (0) or On (1)
RO Bit ND NC PT
07.030 Analog Input 1 Offset (T2) ±100.00 % 0.00 % RW Num US
07.034 Inverter Temperature ±250 °C
RO Num ND NC PT
07.035
Percentage Of d.c. Link Thermal Trip
Level
0to100%
RO Num ND NC PT
07.036 Percentage Of Drive Thermal Trip Level 0 to 100 %
RO Num ND NC PT
07.037 Temperature Nearest To Trip Level 0 to 29999
RO Num ND NC PT
07.051 Analog Input 1 Control (T2) 0 to 5 0 RW Num US
07.061 Analog Input 1 Minimum Reference (T2) 0.00 to 100.00 % 0.00 % RW Num US
07.062
Analog Input 1 At Minimum
Reference (T2)
±100.00 % 0.00 % RW Num US
07.063 Analog Input 1 Maximum Reference (T2) 0.00 to 100.00 % 100.00 % RW Num US
07.064 Analog Input 1 At Maximum Reference (T2) ±100.00 % 100.00 % RW Num US
07.090 Analog Input 1 Destination B (T2) 0.000 to 30.999
RO Num DE PT US
mm.ppp
mm.ppp
Key
Read-write (RW)
parameter
Read-only (RO)
parameter
Input
terminals
Output
terminals
The parameters are all shown in their default settings
07.007
07.008
Analog
Input 1
Scaling
??.???
Any
unprotected
variable
parameter
??.???
x(-1)
Analog Input 1
07.009
Analog
Input 1 Invert
07.028
Analog
Input 1 Current
Loop Loss
07.001
Analog
Input 1
01.036
Analog
Ref. 1
+
+
07.030
Analog Input
1 Offset
T2 Analog Input
1 Mode
07.063
07.064
T2 Analog Input 1
Maximum Reference
T2 Analog Input 1
At Maximum
Reference
07.062
07.061
T2 Analog Input 1
Minimum Reference
T2 Analog Input 1
At Minimum Reference
Analog Input 1
Destination A
Analog Input
1 Control
Analog Input 1
Destination B
07.051
07.010
≥1
07.090
RW Read / Write RO Read only Num Number parameter Bit Bit parameter Txt Text string Bin Binary parameter FI Filtered
ND No default value NC Not copied PT Protected parameter RA Rating dependent US User save PS Power-down save DE Destination
Date Date parameter Time Time parameter