Emmaljunga nxt Twin - Assembly and Use of the Seat Unit; Change Position of the 5-Point Harness; Close the Bumper Bar; Open the Bumper Bar

44 NXT TWIN V2.1
12) 5-POINT HARNESS - BUCKLE YOUR
CHILD
12.1 Place the 5 harness straps in front of the
child so that the child is not sitting on them.
12.2 Assemble the left shoulder and waist straps
by sliding the upper left buckle into the lower
left buckle until it clicks into place.
12.3 Assemble the right shoulder and hip straps
by sliding the upper right buckle into the lower
right buckle until it clicks into place.
12.4 Click the right buckle over the left buckle
until they are held together as a unit. It is very
important that they sit together properly and
that they cannot be pulled apart.
12.5 Lock the harness with the harness lock on
the crotch strap with a “” CLICK “”.
WARNING Always check that the belt is
properly closed by pulling on it.
12.6 Adjust the harness using the sliding adjus-
ters (3) on the shoulder and hip belts so that the
belt ts snugly on the child’s body.
To release the shoulder and waist straps, press
in the buttons on the sides of the harness lock.
WARNING Always fasten the child in with the
harness when the child is sitting in the stroller.
Check that all buckles are correctly fastened and
that the harness is securely assembled in the
stroller.
WARNING Never use the seat if parts of the
5-point harness are missing or if the harness is
damaged. Always check that the harness is
properly closed.
WARNING The 5-point harness contains
magnets or magnetic components. Magnets
that attract each other or a metallic object in the
human body can cause serious injury or death.
Seek medical advice immediately if magnets are
swallowed or inhaled.
WARNING Medical devices such as implanted
pacemakers and debrillators might contain
sensors that respond to magnets and radios
when in close contact. To avoid any potenti-
al interactions with these devices, keep the
harness a safe distance away from your device
(more than 15 cm apart). But consult with your
physician and your device manufacturer for
specic guidelines.
13) CHANGE POSITION OF THE 5-POINT
HARNESS
2.1 Shoulder straps, Remove the hood. Remove
the shoulder pads. Push the shoulder and hip
straps through the holes in the seat cover.
13.2 Open the zipper underneath the seat.Open
the press studs that secure the seat fabric over
the frame. Open the press stud that holds the
adjustment handle.Pull the back plate out of
the fabric and place the shoulder straps in the
desired position in the back plate.Insert the
shoulder straps into the seat fabric in
the same position. Slide the back plate back
into the seat cover.
13.3 - 13.3.3 The Crotch Strap
Pass the crotch strap through the seat cover and
the seat plate. Then mount the crotch strap in
the desired position in the seat plate and pass
the crotch strap in the same position through
the fabric. Close the zipper at the bottom of the
seat. Close the press studs rmly over the frame
on both sides.Thread the strap through the hole
in the fabric and secure it around the adjust-
ment handle with the press stud.
Put the shoulder pads onto the shoulder straps.
WARNING Before you use the pram again
always check that the seat unit fabric is secure
and that all zips are securely and properly
fastened
WARNING It is important that the seat unit
fabric is always correctly tted
WARNING Never use the pram without making
sure the seat unit fabric is correctly assembled
on the frame rst.
SEAT UNIT FLAT
1) ASSEMBLY AND USE OF THE SEAT UNIT
1.1 The seat unit is delivered fully assembled.
Only the bumper bar and the hood need to
be assembled.Insert the bumper bar into the
brackets on both sides of the seat until you hear
a click.
1. 2 Fasten the crotch strap around the bumper
bar.
WARNING The bumper bar should always be
tted when using the seat unit.
WARNING Always check that the bumper bar is
correctly attached to the seat unit before use.
2) OPEN THE BUMPER BAR
2.1 Unfasten the crotch strap.
2.2 Press the button on the inside of the bumper
bar to open
WARNING The bumper bar should always be
tted when using the seat unit.
WARNING Always check that the bumper bar is
correctly attached to the seat unit before use.
3) CLOSE THE BUMPER BAR
3.1 Click the bumper bar into the bracket until
you hear a ”click”.