What does error code M431 mean on Endress+Hauser Deltabar FMD71?
The error code M431 on your Endress+Hauser Measuring Instruments indicates that the calibration carried out would cause the nominal sensor module range to be exceeded or undershot. To address this, check the measuring range, position adjustment, and the setting.
Why is there no display on my Endress+Hauser Measuring Instruments?
If there is no display on your Endress+Hauser Measuring Instruments, it could be due to several reasons. First, the onsite display might be set too bright or too dark. To resolve this, try setting the local display brighter by simultaneously pressing the indicated buttons or darker by pressing the other indicated buttons. Another potential cause is a connector for the local display that is not properly connected, make sure the connector is properly connected. Finally, the onsite display could be defective, in which case it needs to be replaced.
What to do if Endress+Hauser Measuring Instruments device measures incorrectly?
If your Endress+Hauser Measuring Instruments device is measuring incorrectly, the most likely cause is a configuration error. To fix this, check and correct the parameter configuration.
How to fix HART communication not working on Endress+Hauser Measuring Instruments?
If HART communication is not working on your Endress+Hauser Measuring Instruments, it could be due to a few reasons. First, check if the communication resistor (250 ?) is missing or incorrectly installed, and install it correctly. Also, verify that the Commubox is properly connected and set the Commubox selector switch to "HART".
What does error code M434 mean on Endress+Hauser Measuring Instruments and how to troubleshoot it?
The error code M434 on your Endress+Hauser Measuring Instruments can be caused by values for calibration being too close together, lower/upper range values undershooting/overshooting sensor module range limits, a replaced sensor module with an unsuitable customer-specific configuration, or an unsuitable download carried out. To troubleshoot this, check the measuring range and the setting.
What does error code C482 mean on Endress+Hauser Deltabar FMD71 Measuring Instruments?
The error code C482 on your Endress+Hauser Measuring Instruments indicates that the simulation of the current output is switched on, meaning the device is not currently measuring. To resolve this, end the simulation.
What does error code F841 mean on Endress+Hauser Deltabar FMD71 and how to solve it?
The error code F841 on your Endress+Hauser Measuring Instruments indicates overpressure or low pressure, or a defective sensor module. To solve this, check the pressure value.
What does error code S841 mean on Endress+Hauser Deltabar FMD71 Measuring Instruments?
The error code S841 on your Endress+Hauser Measuring Instruments indicates overpressure or low pressure, or a defective sensor module. To address this, check the pressure value.
What does error code F164 mean on Endress+Hauser Deltabar FMD71 and how can I fix it?
The error code F164 on your Endress+Hauser Measuring Instruments indicates that the sensor modules cannot be synchronized or that there are electromagnetic effects outside the permitted range, or defective sensor module(s). To fix this, try restarting the device or replacing the sensor module.
What does error code F083 mean on Endress+Hauser Measuring Instruments and what are possible solutions?
The error code F083 on your Endress+Hauser Measuring Instruments can occur due to electromagnetic effects outside the permitted range or a defective sensor module. You can try restarting the device.
General| Device Type | Differential Pressure Transmitter |
|---|---|
| Measuring Principle | Piezoresistive |
| Output Signal | 4 to 20 mA HART, PROFIBUS PA, FOUNDATION Fieldbus |
| Power Supply | 10.5 to 45 V DC |
| Accuracy | ±0.065% of span |
| Process Temperature | -40 to 150°C (-40 to 302°F) |
| Ambient Temperature | -40 to 85°C (-40 to 185°F) |
| Process Connection | Thread, flange, hygienic connections |
| Housing Material | Aluminum |
| Diaphragm Material | 316L Stainless Steel |
| Communication | HART, PROFIBUS PA, FOUNDATION Fieldbus |
| Approvals | ATEX, IECEx |
| Protection Class | IP67 |
| Process Pressure (Absolute) | Up to 40 bar |
| Application | Level, flow, and differential pressure measurement in liquids, gases, and vapors |
To Next Page