Endress+Hauser Deltapilot M FMB51

Other manuals for Endress+Hauser Deltapilot M FMB51

Technical Information72 pages

Brief Operating Instructions56 pages

Questions and Answers

C
Christopher WilkinsonAug 14, 2025
What to do if Endress+Hauser Deltapilot M FMB51 Measuring Instruments show 'Process pressure'?
- M
  Michelle SanchezAug 14, 2025
  If the Endress+Hauser Measuring Instruments display 'Process pressure', it could be due to electromagnetic effects exceeding the specifications in the technical data, or the presence of overpressure or low pressure. You should check the pressure value. If this doesn't resolve the issue, try restarting the device or performing a reset.
R
Robert JohnsonAug 17, 2025
Why Endress+Hauser Measuring Instruments show 'Working range P'?
- J
  Jill HinesAug 17, 2025
  The 'Working range P' error on Endress+Hauser Measuring Instruments indicates the presence of overpressure and low pressure, electromagnetic effects exceeding the specifications, or a defective sensor. Check the process pressure and the sensor range to resolve the issue.
U
usotoAug 20, 2025
What to do if Endress+Hauser Deltapilot M FMB51 Measuring Instruments show 'Sensor conn.'?
- J
  joyjohnsonAug 21, 2025
  If the Endress+Hauser Measuring Instruments display 'Sensor conn.', the cable connection between the sensor and main electronics might be disconnected, the sensor might be defective or electromagnetic effects are greater than specifications in the technical data. Check the sensor cable. If this doesn't resolve the issue, replace the electronics.
M
Megan CortezAug 25, 2025
What to do if Endress+Hauser Measuring Instruments show 'Initialization'?
- T
  Thomas GarzaAug 25, 2025
  If the Endress+Hauser Measuring Instruments display 'Initialization', the cable connection between the sensor and main electronics might be disconnected, the sensor might be defective or electromagnetic effects are greater than specifications in the technical data. Perform a reset or check the sensor cable.
T
Tamara DominguezAug 27, 2025
What to do if Endress+Hauser Measuring Instruments show 'Electronics'?
- J
  Jessica KrauseAug 27, 2025
  If the Endress+Hauser Measuring Instruments display 'Electronics', try restarting the device or replacing the electronics.
H
Helen RyanAug 30, 2025
What to do if Endress+Hauser Measuring Instruments show 'Permanent mem.'?
- R
  Roger MurphyAug 31, 2025
  If the Endress+Hauser Measuring Instruments display 'Permanent mem.', try restarting the device.
L
Lindsey CarterSep 3, 2025
What to do if Endress+Hauser Deltapilot M FMB51 show 'Current simul.'?
- S
  Shane MyersSep 3, 2025
  If the Endress+Hauser Measuring Instruments are showing 'Current simul.', end the simulation.
T
Tina ColonSep 6, 2025
What to do if Endress+Hauser Measuring Instruments show 'Error simul.'?
- D
  Dylan PayneSep 6, 2025
  If the Endress+Hauser Measuring Instruments are showing 'Error simul.', end the simulation.
B
briancampbellSep 10, 2025
What to do if Endress+Hauser Measuring Instruments show 'Measure simul.'?
- A
  Andrea ThompsonSep 10, 2025
  If the Endress+Hauser Measuring Instruments are showing 'Measure simul.', end the simulation.

Summary

1 Safety Instructions

1.1 Designated Use

Describes the intended use of Cerabar M, Deltabar M, Deltapilot M devices.

1.2 Installation, Commissioning, Operation

Outlines the procedures for installing, commissioning, and operating the devices.

1.3 Operational and Process Safety

Details safety measures for operational and process safety, including warnings.

1.3.1 Hazardous Areas

Covers safety considerations for devices used in hazardous areas, requiring specific documentation.

3 Installation

3.3 Installing Cerabar M

Provides specific instructions for installing the Cerabar M transmitter, including diaphragm seals.

4 Wiring

4.1 Connecting the Device

Explains the procedure and diagram for connecting the device's electrical wiring.

4.2 Connecting the Measuring Unit

5 Operation

5.1 Operating Options

5.2 Operation Without Operating Menu

5.3 Operation With an Operating Menu

5.3.3 Operation With a Device Display

5.3.4 Operation Via HART Handheld Terminal

5.3.5 Operation Via FieldCare

5.3.7 Resetting to Factory Settings

6 Commissioning

6.1 Function Check

Outlines the necessary post-installation and post-connection checks before commissioning.

6.2 Commissioning Without an Operating Menu

Explains commissioning steps for pressure measurement without a local display.

6.2.2 Level Measuring Mode

6.2.3 Flow Measuring Mode

6.3 Commissioning With an Operating Menu

Covers commissioning steps including language, measuring mode, and pressure unit selection.

6.4 Position Zero Adjustment

Explains how to correct pressure shifts caused by device orientation.

6.5 Level Measurement

Provides information and an overview of level measurement methods.

6.5.3 In Pressure Level Selection

Details wet calibration for "In pressure" level selection with reference pressure.

6.5.4 In Pressure Level Selection

Details dry calibration for "In pressure" level selection without reference pressure.

6.5.5 In Height Level Selection

Details wet calibration for "In height" level selection with reference pressure.

6.5.6 In Height Level Selection

Details dry calibration for "in height" level selection without reference pressure.

6.5.7 Calibration With Partially-Filled Tank

6.6 Linearization

Covers manual entry of the linearization table for volume or mass measurement.

6.6.2 Manual Entry of Linearization Table via Operating Tool

6.6.3 Semi-Automatic Entry of Linearization Table

6.7 Pressure Measurement

Details dry calibration for pressure measurement without reference pressure.

6.7.2 Calibration With Reference Pressure

Describes wet calibration for pressure measurement with reference pressure.

6.8 Electrical Differential Pressure Measurement

Explains how to measure differential pressure using two gauge pressure sensors.

6.9 Differential Pressure Measurement

Covers preparatory steps for differential pressure measurement with Deltabar M.

6.10 Flow Measurement

Provides information on flow measurement principles using Deltabar M.

6.11 Level Measurement

Details preparatory steps for level measurement with Deltabar M in open containers.

6.11.2 Information on Level Measurement

6.11.4 Level Selection In Pressure

Details wet calibration for "In pressure" level selection with reference pressure.

6.11.5 Level Selection In Pressure

Details dry calibration for "In pressure" level selection without reference pressure.

6.11.6 Level Selection In Height

Details dry calibration for "in height" level selection without reference pressure.

6.11.7 Level Selection In Height

Details wet calibration for "in height" level selection with reference pressure.

8 Troubleshooting

8.1 Messages

Lists possible error messages, their causes, and recommended measures based on NAMUR NE107 codes.

8.2 Response of Output to Errors