What to do if Endress+Hauser Measuring Instruments show 'Process pressure'?
If the Endress+Hauser Measuring Instruments display 'Process pressure', it could be due to electromagnetic effects exceeding the specifications in the technical data, or the presence of overpressure or low pressure. You should check the pressure value. If this doesn't resolve the issue, try restarting the device or performing a reset.
Why Endress+Hauser Cerabar M PMC51 show 'Working range P'?
The 'Working range P' error on Endress+Hauser Measuring Instruments indicates the presence of overpressure and low pressure, electromagnetic effects exceeding the specifications, or a defective sensor. Check the process pressure and the sensor range to resolve the issue.
What to do if Endress+Hauser Measuring Instruments show 'Sensor conn.'?
If the Endress+Hauser Measuring Instruments display 'Sensor conn.', the cable connection between the sensor and main electronics might be disconnected, the sensor might be defective or electromagnetic effects are greater than specifications in the technical data. Check the sensor cable. If this doesn't resolve the issue, replace the electronics.
What to do if Endress+Hauser Measuring Instruments show 'Initialization'?
If the Endress+Hauser Measuring Instruments display 'Initialization', the cable connection between the sensor and main electronics might be disconnected, the sensor might be defective or electromagnetic effects are greater than specifications in the technical data. Perform a reset or check the sensor cable.
What to do if Endress+Hauser Cerabar M PMC51 show 'Electronics'?
If the Endress+Hauser Measuring Instruments display 'Electronics', try restarting the device or replacing the electronics.
What to do if Endress+Hauser Cerabar M PMC51 Measuring Instruments show 'Permanent mem.'?
If the Endress+Hauser Measuring Instruments display 'Permanent mem.', try restarting the device.
What to do if Endress+Hauser Cerabar M PMC51 show 'Current simul.'?
If the Endress+Hauser Measuring Instruments are showing 'Current simul.', end the simulation.
What to do if Endress+Hauser Cerabar M PMC51 Measuring Instruments show 'Error simul.'?
If the Endress+Hauser Measuring Instruments are showing 'Error simul.', end the simulation.
What to do if Endress+Hauser Cerabar M PMC51 show 'Measure simul.'?
If the Endress+Hauser Measuring Instruments are showing 'Measure simul.', end the simulation.
General| Type | Cerabar M PMC51 |
|---|---|
| Measuring Principle | Piezoresistive |
| Output Signal | 4-20 mA HART |
| Housing | Aluminum, stainless steel |
| Approvals | ATEX, IECEx, CSA, FM |
| Communication | HART |
| Operating Temperature | -40°C to +85°C |
| Ambient Temperature | -40°C to +85°C |
| Protection Class | IP66 |
| Electrical Connection | Cable gland |
| Power Supply | 10.5 to 45 V DC |
| Process Connection | Threads, flanges, hygienic connections |
Contains technical data for Cerabar M, Deltabar M, Deltapilot M.
Details installation, operation, commissioning, maintenance, and troubleshooting.
Provides installation, wiring, operation, and commissioning steps.
Specifies the intended use for Cerabar M, Deltabar M, and Deltapilot M devices.
Details requirements for safe installation, connection, commissioning, and operation.
Discusses safety measures during configuration, testing, and servicing.
Covers safety instructions for devices used in hazardous locations.
Explains safety symbols, warnings, cautions, and notes used in the manual.
Information on identifying the device via its nameplate and designation.
Lists the items included in the device package.
Confirms device compliance with EC Directives and safety requirements.
Lists registered trademarks and labels associated with the device.
Procedures for checking shipment and proper storage of the device.
Information regarding necessary conditions before device installation.
Specific instructions for installing the Cerabar M device.
Specific installation guidance for Cerabar M models without diaphragm seals.
Specific installation guidance for Cerabar M models with diaphragm seals.
Specific instructions for installing the Deltabar M device.
Guidance on optimal mounting position for Deltabar M devices.
Specific instructions for installing the Deltapilot M device.
General guidelines for installing Deltapilot M devices.
Step-by-step guide for electrical connection of the device.
Instructions for connecting the measuring unit to the device.
Guidelines for proper shielding and potential equalization.
Instructions for connecting a HART handheld terminal.
Connecting the Commubox FXA195 for operation with FieldCare.
Connecting devices to local potential equalization for hazardous areas.
Information and instructions for optional overvoltage protection.
Checklist to perform after completing electrical installation.
Overview of different methods for operating the device.
Operating the device using keys and DIP switches without a display.
Locating and function of operating keys and DIP switches.
Operating the device using its menu structure.
Explanation of user roles and their responsibilities in operating the device.
Details the hierarchical structure and submenus of the operating menu.
Instructions for operating the device using its optional local display.
Using a HART handheld terminal for parameter setup and operation.
Using FieldCare software for device configuration and asset management.
Procedures for locking and unlocking device operation.
How to reset device parameters to factory or order configuration settings.
Steps for performing post-installation and post-connection checks before commissioning.
Commissioning the device using keys without a display.
Commissioning the device using its menu structure.
Correcting pressure shifts caused by device orientation.
Information and overview for level measurement tasks.
Wet calibration for level measurement using pressure references.
Dry calibration for level measurement without pressure references.
Dry calibration for level measurement using height references.
Methods for linearizing measurement data.
Procedures for calibrating pressure measurement.
Measuring differential pressure using two gauge pressure sensors.
Information and preparatory steps for differential pressure measurement.
Information and preparatory steps for flow measurement.
Information and preparatory steps for level measurement.
Instructions for cleaning the exterior of the device.
List of possible error and status messages with causes and measures.
Defines output behavior based on specific error conditions.
Information on the Endress+Hauser repair concept and general repair guidelines.
Specific safety and procedural requirements for repairing Ex-certified devices.
Guidance on how to find and order spare parts for the device.
Procedures and requirements for returning a device for repair or inspection.
Instructions for proper disposal and recycling of device components.
Details software versions and corresponding documentation for different devices.
A comprehensive list of all device parameters with their locations and page references.
To Next Page
