Hardware Installation and Maintenance Manual v
LIST OF FIGURES
Figure 1–1. Schematic of a typical laser diode absorption spectrometer . . . . . . 1-6
Figure 1–2. Typical raw signal from a laser diode absorption spectrometer
with and without mirror contamination . . . . . . . . . . . . . . . . . . . . 1-7
Figure 1–3. Typical normalized absorption signal from a laser diode
absorption spectrometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
Figure 1–4. Typical normalized 2
f signal; species concentration is
proportional to peak height . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9
Figure 1–5. 2-Pack analyzer architecture . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
Figure 1–6. Analyzer A ARM9 electronics control board (AC) showing
signal terminal block and alarm relays. . . . . . . . . . . . . . . . . . . . 1-11
Figure 1–7. Analyzer A ARM9 electronics control board (DC) showing
signal terminal block and alarm relays. . . . . . . . . . . . . . . . . . . . 1-12
Figure 1–8. Analyzer B HC12 electronics control board (AC) showing
signal terminal block and alarm relays. . . . . . . . . . . . . . . . . . . . 1-13
Figure 1–9. Analyzer B HC12 electronics control board (DC) showing
signal terminal block and alarm relays. . . . . . . . . . . . . . . . . . . . 1-14
Figure 3–1. Lifting points and mounting dimensions . . . . . . . . . . . . . . . . . . . . 3-2
Figure 3–2. AC and DC connections for the electronics control board
terminal block in the Analyzer A electronics enclosure . . . . . . . . . . 3-7
Figure 3–3. AC and DC connections for the electronics control board
terminal block in the Analyzer B electronics enclosure . . . . . . . . . . 3-8
Figure 3–4. AC connection terminal block for enclosure heater . . . . . . . . . . . . 3-9
Figure 3–5. Applying conduit lubricant . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
Figure 3–6. Analyzer A mating terminal block (TB2) for connecting
signal cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
Figure 3–7. Analyzer B mating terminal block (TB2) for connecting
signal cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
Figure 3–8. Analyzer 4-20 mA board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17
Figure A–1. Outline and mounting dimensions, fixed mount, non-validation,
2-Pack analyzer system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-5
Figure A–2. SCS schematic, fixed mount, non-validation, 2-Pack analyzer
system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-6
Figure A–3. SCS Bill of Materials, fixed mount, non-validation, 2-Pack
analyzer system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-7
Figure A–4. SCS schematic, fixed mount, non-validation, solenoid/air
actuated valve option for 2-Pack analyzer system . . . . . . . . . . . . . A-8
Figure A–5. SCS schematic, fixed mount, non-validation, 1-pt air actuated
valve/liquid knock-out option for 2-Pack analyzer system . . . . . . . A-9
Figure A–6. SCS schematic, fixed mount, non-validation, high H2S purge
option for 2-Pack analyzer system . . . . . . . . . . . . . . . . . . . . . . A-10
Figure A–7. Power and signal wiring diagram, fixed mount, non-validation,
2-Pack analyzer system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-11
To Next Page
Loading...
