Why is electrical noise affecting my Endress+Hauser SpectraSensors SS2100r Measuring Instruments?
High levels of electrical noise can interfere with laser operation of Endress+Hauser Measuring Instruments. To address this, always connect the analyzer to a properly grounded power source.
How to prevent gas leaks in Endress+Hauser SpectraSensors SS2100r?
To prevent gas leaks in Endress+Hauser Measuring Instruments, periodically leak-test the supply lines, especially after relocation, replacement, or factory service with reconnection of supply lines. Also, avoid using plastic tubing for sample lines; instead, use 1/4” O.D. x 0.035” wall thickness, seamless stainless steel tubing.
What to do if Endress+Hauser SpectraSensors SS2100r are not operating at start up?
If your Endress+Hauser Measuring Instruments are not operating at start up, ensure that the power is connected to both the analyzer and the power source, and that the switch is turned on.
What to do if Endress+Hauser Measuring Instruments are not operating after start up?
If your Endress+Hauser Measuring Instruments are not operating after start up, verify that the power source is adequate (120 VAC @ 50-60 Hz, 9-16 VDC, 18-32 VDC), referring to the Calibration Certificate for specific power requirements. Also, check the fuse(s) and replace any blown fuses with equivalent ones, referring to Table 1–1.
How to deal with contamination in Endress+Hauser Measuring Instruments?
Contamination in Endress+Hauser Measuring Instruments can be addressed by periodically cleaning the gas sampling lines due to long exposure to high humidity. Additionally, ensure that a membrane separator filter (included with most systems) is installed ahead of the analyzer and operating normally. To clean the sampling line turn off the sample valve at the tap in accordance with site lock-out, tag-out rules. Disconnect the gas sampling line from the sample supply port of the analyzer. Wash the sampling line with isopropyl alcohol or acetone and blow dry with mild pressure from a dry air or nitrogen source. Once the sampling line is completely free of solvent, reconnect the gas sampling line to the sample supply port of the analyzer. Check all connections for gas leaks using a liquid leak ...
Alerts users to potential hazards and important safety information.
Explains the meaning of symbols used for warnings and instructions within the manual.
Guides users on navigating and utilizing the manual's features and content.
Introduces the SS2100r analyzers and their fundamental operating principles.
Details the tunable diode laser absorption spectroscopy (TDLAS) principle used by the analyzers.
Describes the WMS technique used for sophisticated signal detection.
Guides users through the analyzer's front, rear panels, and internal compartments.
Details the components and layout of the analyzer's main electronics.
Explains safety symbols and labels found on the equipment and in the manual.
Lists the expected contents of the analyzer's shipping crate for verification.
Provides instructions for unpacking and inspecting the analyzer for physical damage.
Covers rack mounting procedures and electrical power connection for the analyzer.
Guides on connecting signal, alarm outputs, and sample gas lines to the analyzer.
Guides on calibrating the analyzer's 4-20 mA analog output for accuracy.
Describes the process of conditioning the analyzer system for stable and accurate readings.
Discusses factors affecting scrubber lifespan and the function of efficiency indicators.
Provides step-by-step instructions for replacing the H2S scrubber and indicator.
Advises on the proper disposal procedures for depleted H2S scrubbers.
Lists key performance metrics including range, repeatability, and response time.
Details environmental operating ranges and application-specific data.
Covers electrical input requirements and communication interface details.
Lists replaceable electronic, conditioning system, and general spare parts.
Addresses potential hazards and necessary safety actions for personnel during analyzer service.
Discusses issues like gas leaks, contamination, and environmental factors affecting measurements.
Provides instructions and necessary tools for cleaning analyzer mirrors.
Lists common instrument problems and their corresponding troubleshooting responses.
Provides contact details, repair order process, and warranty terms for support.
General| Type | Gas Analyzer |
|---|---|
| Technology | Tunable Diode Laser Absorption Spectroscopy (TDLAS) |
| Operating Temperature | -20 to +50°C (-4 to +122°F) |
| Enclosure | Stainless steel |
| Measured gas | H2O |
| Measurement Range | Application dependent |
| Accuracy | ±1% of reading or better |
| Repeatability | +/- 1% of reading |
| Operating Pressure | Up to 20 bar (290 psi) depending on application |
| Power Supply | 24 VDC |
| Outputs | 4-20 mA |
| Communication Protocols | Modbus |
| Mounting | Wall mount |
| Enclosure Rating | IP66 |
| Certifications | ATEX, IECEx |
To Next Page