How to fix the Epever Tracer1206AN charging LED indicator when it's off during the daytime with proper sunshine on the PV modules?
If the charging LED indicator is off during the daytime when sunshine falls on PV modules properly, confirm that the PV and battery wire connections are correct and tight.
What to do if the Epever Tracer1206AN load has no output and the load/fault icon blink?
If the load has no output and the load/fault icon is blinking on your Epever Controller, it indicates a load overload. Reduce the number of connected electrical devices, restart the controller, or wait for one night-day cycle (night time > 3 hours).
Why does the Epever Controller battery level show full, with the battery frame and fault icon blinking?
If the battery level on your Epever Controller shows full, but the battery frame and fault icon are blinking, it signifies a battery over voltage. Check if the battery voltage exceeds the OVD (over voltage disconnect voltage) and disconnect the PV.
What to do if there is a Load Short Circuit on the Epever Tracer1206AN Controller?
If there is a load short circuit, carefully check the load connections and clear the fault. Restart the Epever Controller and wait for one night-day cycle (night time > 3 hours).
What does it mean when the Epever Tracer1206AN Controller battery level is empty, battery frame blinks, and fault icon blinks?
When the battery level shows empty, the battery frame blinks, and the fault icon blinks on the Epever Controller, it indicates that the battery is overheating. The controller will automatically turn the system off. The controller will resume once the temperature declines below 55 ºC.
Why is my Epever Tracer1206AN Controller not working even though the wire connections are correct?
If your Epever Controller is not working despite correct wiring, the battery voltage may be too low. Check the battery voltage; it needs to be at least 8V to activate the controller.
What to do if Epever Tracer1206AN shows overload?
If your Epever Controller indicates an overload, reduce the number of connected electrical devices. Then, restart the controller or press the button to clear the fault.
What to do if Epever Controller has load short-circuit?
If the Epever Controller displays a load short-circuit, carefully check the load connections and clear the fault. Then, restart the controller or press the button to clear the faults.
What to do if Epever Controller indicates battery over discharged?
If your Epever Controller indicates that the battery is over discharged, the load will recover when the battery voltage is restored to or above the LVR (low voltage reconnect voltage). In the meantime, use alternative methods to recharge the battery.
How to fix PV array open-circuit on Epever Controller?
To address a PV array open-circuit issue with your Epever Controller, verify that the PV array connections are correct and securely tightened.
General safety guidelines for installation and operation of the MPPT controller.
Important precautions and general guidance for the installation process.
Provides guidelines for mounting the controller, including clearance and ventilation.
Covers setting parameters like battery type, voltage control, user settings, and load modes.
Details the controller's protection features against various electrical faults.
Provides solutions for common problems, faults, and error indications.
Outlines recommended periodic maintenance tasks for optimal performance.
Lists electrical specifications for all Tracer AN series controller models.
General| Model | Tracer1206AN |
|---|---|
| Type | MPPT Solar Charge Controller |
| Rated Charge Current | 10A |
| Rated Load Current | 10A |
| Max. PV Input Power | 130W (12V system) / 260W (24V system) |
| Battery Type | Sealed, Gel, Flooded, User |
| MPPT Tracking Efficiency | 99% |
| Max. Conversion Efficiency | 98% |
| Efficiency | 98% |
| Temperature Compensation | -3mV/°C/2V(Default) |
| Altitude | ≤3000m |
| Cooling | Natural Cooling |
| PV Input Voltage | 12V |
| Charge Algorithm | PWM |
| Protection | Short circuit |
| Operating Temperature | -20°C to +50°C |
| Storage Temperature | -30°C to +70°C |
| Grounding | Negative ground |
| Nominal System Voltage | 12VDC / 24VDC Auto work |
To Next Page