Epson ELPLP29 - User Manual

Questions and Answers

D
Danielle MichaelAug 19, 2025
What to do if the Epson Projector red warning indicator is on due to overheating?
- F
  fergusonstephenAug 19, 2025
  If the red warning indicator is on and indicates a high internal temperature (overheating), wait about 5 minutes without using the Epson projector. Then, unplug the power cable. Ensure the air filter and ventilation outlet are clear and that the projector isn't against a wall. If the air filter is dirty, clean it. When you plug the power cable back in, the projector will return to its previous state.
A
andersonbrittanyAug 21, 2025
Why does the Epson ELPLP29 Projector remote control not work?
- E
  Elizabeth AdamsAug 21, 2025
  If the remote control for your Epson projector isn't working, check if direct sunlight or strong light is shining on the infrared receiver. Ensure the remote isn't too far from the projector and that the infrared transmitter is facing the receiver. Also, verify the battery insulating tape has been removed, the battery isn't dead, and that it's inserted correctly.
W
William SampsonAug 23, 2025
Why is there no sound coming from my Epson ELPLP29?
- S
  Susan CalhounAug 25, 2025
  If you're not hearing any sound from your Epson projector, check if A/V Mute is activated, if the volume is turned down, and if the audio source is connected correctly.
C
Connor SandersAug 26, 2025
What to do if my Epson ELPLP29 Projector says 'No signal'?
- T
  Teresa HutchinsonAug 26, 2025
  If your Epson projector displays 'No signal', check the following: Make sure external video output has been selected on the computer, the input source is properly selected, the cables are correctly connected, and that the connected computer or video source is powered on.
B
bethany16Aug 27, 2025
How to fix an out of focus image on my Epson Projector?
- J
  Joseph WestAug 27, 2025
  If your Epson projector image is out of focus, ensure the Sync, Tracking, and Position settings are correctly adjusted. Check that the image signal format settings are correct, and that the projector is positioned at right angles to the screen and at the correct distance. Also, make sure the front feet are set correctly, the lens is clean and free of condensation, the focus is properly adjusted, and the lens cover is removed.
J
James BlakeAug 29, 2025
Why is my Epson ELPLP29 Projector image so dark?
- K
  katie71Aug 29, 2025
  If the image from your Epson projector is dark, consider whether the lamp needs replacement and check if the image brightness and contrast have been adjusted correctly.
J
Jennifer JonesSep 1, 2025
How to fix vertical stripes on my Epson ELPLP29 image?
- D
  davismelanieSep 1, 2025
  If vertical stripes appear in the image of your Epson projector, try adjusting the "Tracking" setting.
G
Gary KeySep 3, 2025
What to do if the Epson ELPLP29 red warning indicator is on due to a lamp problem?
- S
  Sean TateSep 3, 2025
  If the red warning indicator on your Epson projector is lit due to a lamp problem, disconnect the power cable. Remove the lamp and check if it's broken. If not, reinstall it, reconnect the power cable, and press the power button. If the lamp is broken, contact your dealer.
C
Chelsea WebbSep 5, 2025
Why is the image distorted on my Epson ELPLP29 Projector?
- K
  kimberlycardenasSep 5, 2025
  If the image from your Epson projector appears distorted or contains interference, ensure the Sync, Tracking, and Position settings are correctly adjusted. Also, verify the image signal format settings are correct, the correct resolution is selected, and the cables are connected properly. Check if using an extension cable is causing the issue.
E
Elizabeth NelsonSep 7, 2025
Why is only part of the image displayed on my Epson ELPLP29 Projector?
- H
  Holly WareSep 7, 2025
  If only part of the image is displayed on your Epson projector, try changing the resolution for the laptop computer or computer with a LCD screen. Also, verify that the aspect ratio is set correctly, the computer is not set for dual display, the correct resolution has been selected, the Position has been adjusted correctly, and the E-Zoom function isn't enlarging the image.