Epson EMP-822 - User Manual

Other manuals for Epson EMP-822

Questions and Answers

B
buckleysherylSep 23, 2025
Why am I not receiving mail notifications when a problem occurs with my Epson Projector?
- S
  Sarah RodgersSep 23, 2025
  If you're not receiving mail notifications for your Epson Projector, consider the following: * Ensure 'Standby Mode' is set to 'Network On' in the configuration menu. * Mail cannot be sent if the projector experiences a sudden, fatal stop. * Check that your electrical outlet or power source is functioning correctly. * Verify the LAN cable is correctly connected. * Confirm that 'Mail' is correctly configured in the configuration menu.
B
Brian DavisAug 25, 2025
Why is there no audio from my Epson Projector, or the audio is too low?
- P
  Patricia JonesAug 25, 2025
  If you're experiencing low or no audio from your Epson Projector, consider the following: * Verify the audio source is correctly connected to the Audio port. * Adjust the volume to a suitable level. * Ensure A/V Mute is not active by pressing the [A/V Mute] button on the remote control. * Use an audio cable labelled 'No resistance'.
M
Melissa BrownAug 25, 2025
How to fix the Epson EMP-822 Projector remote control when it's not working?
- J
  John SanchezAug 26, 2025
  If your Epson Projector's remote control isn't working, try these steps: * Point the remote control directly at the remote receiver on the projector. * Ensure you are within the remote control's operating range (about 6 m). * Make sure direct sunlight or strong light isn't shining on the remote receiver. * Check the 'Remote Receiver' setting in the configuration menu. * Verify the batteries are correctly inserted and replace them if necessary. * If a remote button has been pressed for more than 30 seconds, release it to resume normal operation.
C
Chad StephensAug 27, 2025
Why won't my Epson Projector power on?
- T
  Timothy WellsAug 27, 2025
  If your Epson Projector won't power on, try these steps: * Press the [Power] button to turn the power on. * Ensure the power cable is correctly connected and that the outlet is functioning. * Reinsert the power cable; if it still doesn't work, disconnect the projector and contact your local dealer. * If the operation lock is set to 'Full Lock', press and hold the [Enter] button on the control panel for about seven seconds to release the lock. * Check the 'Remote Receiver' setting in the configuration menu. * Press the [Power] button to turn the power back on.
C
Cheryl TorresAug 27, 2025
Why does my Epson EMP-822 show a High Temp Warning?
- P
  Patrick OconnellAug 27, 2025
  If your Epson Projector is showing a High Temp Warning, check that the air filter and air exhaust vent are not blocked, and make sure the projector isn't placed directly against a wall. If the air filter is clogged, clean or replace it.
B
bartlettcindySep 13, 2025
How to fix an internal error on Epson EMP-822 Projector?
- M
  Madison ReyesSep 14, 2025
  If your Epson Projector displays an Internal Error, disconnect the AC cable, then reconnect it, and turn the power on. If the same error occurs, replace the Optical Engine and MAB set because the MA board is broken.
X
xgarciaSep 12, 2025
What does internal error RAM mean on Epson Projector?
- A
  Amy EdwardsSep 12, 2025
  If your Epson Projector displays 'Internal error RAM (RA)', and it is caused by an abnormality of the RAM, replace the Optical Engine and MAB set.
R
ryan67Sep 12, 2025
What does internal error ROM mean on Epson EMP-822?
- G
  George LopezSep 13, 2025
  If your Epson Projector displays 'Internal error ROM (RO)', and it is caused by an abnormality of the MAB, replace the Optical Engine and MAB set.
J
Jennifer StricklandSep 4, 2025
What causes a lighting failure on my Epson EMP-822 Projector?
- J
  Jason TorresSep 4, 2025
  If your Epson Projector is experiencing a Lighting Failure (LF), start by replacing the AS Lamp Unit if the V-LA value is abnormally high or if the lamp has failed. If the Ballast’s drive waveform is unstable, replace the PS Ballast Assy. Also, if the filter is clogged due to overheating, replace the Air Filter Assy.
T
Tyler SanchezSep 2, 2025
Why is nothing appearing on the external monitor connected to my Epson Projector?
- A
  Andrea CarterSep 2, 2025
  Only computer images from the Computer1 or Computer Input port can be displayed on an external monitor connected to your Epson Projector. Ensure you are projecting images from one of these ports.

Epson EMP-822 Specifications

General

Resolution	1024 x 768 (XGA)
Contrast Ratio	400:1
Display Technology	3LCD
Projection Size	30 - 300 inches
Input Ports	S-Video
Noise Level	28 dB (eco)
Lamp Life	2000 hours (Normal mode), 3000 hours (Eco mode)
Power Consumption	280 W (Normal mode), 225 W (Eco mode)