Epson EMP-822 User Manual (English)

Other manuals for Epson EMP-822

Questions and Answers:

A
Angela DavisSep 5, 2025
How to fix a fan error on an Epson EMP-822?
- W
  walvarezSep 5, 2025
  If your Epson Projector displays 'Fan error (FN)', it might be due to several causes. If a fin is broken, replace the fan. If the fan's revolutions are abnormal, or the cables/conduction are damaged, replace the fan. Also, correct the connection if the connectors are inappropriately connected. Clean the fan if dust has accumulated on it. In case of micro-computer abnormality, replace the Optical Engine and MAB set. Re-download the parameters if the thermal parameters are broken.
B
Brian DavisAug 25, 2025
Why is there no audio from my Epson Projector, or the audio is too low?
- P
  Patricia JonesAug 25, 2025
  If you're experiencing low or no audio from your Epson Projector, consider the following: * Verify the audio source is correctly connected to the Audio port. * Adjust the volume to a suitable level. * Ensure A/V Mute is not active by pressing the [A/V Mute] button on the remote control. * Use an audio cable labelled 'No resistance'.
M
Melissa BrownAug 25, 2025
How to fix the Epson EMP-822 Projector remote control when it's not working?
- J
  John SanchezAug 26, 2025
  If your Epson Projector's remote control isn't working, try these steps: * Point the remote control directly at the remote receiver on the projector. * Ensure you are within the remote control's operating range (about 6 m). * Make sure direct sunlight or strong light isn't shining on the remote receiver. * Check the 'Remote Receiver' setting in the configuration menu. * Verify the batteries are correctly inserted and replace them if necessary. * If a remote button has been pressed for more than 30 seconds, release it to resume normal operation.
C
Chad StephensAug 27, 2025
Why won't my Epson Projector power on?
- T
  Timothy WellsAug 27, 2025
  If your Epson Projector won't power on, try these steps: * Press the [Power] button to turn the power on. * Ensure the power cable is correctly connected and that the outlet is functioning. * Reinsert the power cable; if it still doesn't work, disconnect the projector and contact your local dealer. * If the operation lock is set to 'Full Lock', press and hold the [Enter] button on the control panel for about seven seconds to release the lock. * Check the 'Remote Receiver' setting in the configuration menu. * Press the [Power] button to turn the power back on.
C
Cheryl TorresAug 27, 2025
Why does my Epson EMP-822 show a High Temp Warning?
- P
  Patrick OconnellAug 27, 2025
  If your Epson Projector is showing a High Temp Warning, check that the air filter and air exhaust vent are not blocked, and make sure the projector isn't placed directly against a wall. If the air filter is clogged, clean or replace it.
T
Terrence TannerAug 28, 2025
How to fix fuzzy or out of focus images on my Epson EMP-822?
- B
  bowenAug 28, 2025
  To resolve fuzzy or out-of-focus images on your Epson Projector: * Adjust the focus by turning the focus ring. * Ensure the projector is set up within the recommended projection distance range. * Reduce the projection angle to lower the amount of keystone correction, as a large keystone adjustment can cause fuzziness.
X
xgarciaSep 12, 2025
What does internal error RAM mean on Epson Projector?
- A
  Amy EdwardsSep 12, 2025
  If your Epson Projector displays 'Internal error RAM (RA)', and it is caused by an abnormality of the RAM, replace the Optical Engine and MAB set.
J
Jennifer StricklandSep 4, 2025
What causes a lighting failure on my Epson EMP-822 Projector?
- J
  Jason TorresSep 4, 2025
  If your Epson Projector is experiencing a Lighting Failure (LF), start by replacing the AS Lamp Unit if the V-LA value is abnormally high or if the lamp has failed. If the Ballast’s drive waveform is unstable, replace the PS Ballast Assy. Also, if the filter is clogged due to overheating, replace the Air Filter Assy.
T
Tyler SanchezSep 2, 2025
Why is nothing appearing on the external monitor connected to my Epson Projector?
- A
  Andrea CarterSep 2, 2025
  Only computer images from the Computer1 or Computer Input port can be displayed on an external monitor connected to your Epson Projector. Ensure you are projecting images from one of these ports.
M
Michele WalshSep 3, 2025
What to do if my Epson EMP-822 shows a lamp problem or failure?
- K
  Katelyn CervantesSep 3, 2025
  If your Epson Projector displays a 'Lamp problem', 'Lamp failure' or indicates that the 'Lamp cover is open', first ensure the Lamp Lid is securely fixed and the lamp itself is properly secured. Remove the lamp to inspect for any damage. If no cracks are visible, re-fit the lamp and power on the projector. If the error persists, replace the lamp. Also, if using the projector at an altitude of 1500 m or more, set "High Altitude Mode" to "On." Clean or replace the filter if it's clogged.

Epson EMP-822 Specifications

General

Resolution	1024 x 768 (XGA)
Contrast Ratio	400:1
Display Technology	3LCD
Projection Size	30 - 300 inches
Input Ports	S-Video
Noise Level	28 dB (eco)
Lamp Life	2000 hours (Normal mode), 3000 hours (Eco mode)
Power Consumption	280 W (Normal mode), 225 W (Eco mode)