Epson EMP-822 User Manual (English)

Other manuals for Epson EMP-822

Questions and Answers:

L
lynn50Aug 22, 2025
What to do if my Epson Projector displays 'No Signal'?
- M
  Michael VargasAug 23, 2025
  If your Epson Projector displays a 'No Signal' message, try the following: * Ensure all cables required for projection are securely connected. * Change the image source by pressing the [Source Search] button on the remote control or the control panel. * Turn on the power for the connected equipment. * If image signals are only outputting to the computer's LCD monitor, change the output to an external destination as well as the computer's own monitor.
J
jeffreymcneilSep 1, 2025
Why do no images appear on my Epson EMP-822?
- L
  Lawrence JohnsonSep 1, 2025
  If no images appear on your Epson Projector, try these solutions: * Press the [Power] button to turn the power on. * Ensure the projector's power cable is correctly connected and the outlet is working. * Press the [A/V Mute] button on the remote to cancel A/V Mute. * Open the A/V mute slide. * Reset all settings by navigating to 'Reset' - 'Reset All'. * Change the image signal format setting according to the signal for the connected equipment.
C
charles12Aug 30, 2025
Why does my Epson EMP-822 Projector projection stop automatically?
- A
  Amy DuarteAug 31, 2025
  If your Epson Projector stops projecting automatically, it might be due to the Sleep Mode being enabled. Press the [Power] button to turn the power back on. If you prefer, you can disable 'Sleep Mode' in the settings.
S
Samantha HughesAug 30, 2025
Why are images dark on my Epson Projector?
- D
  Darren ChristianAug 30, 2025
  If images appear dark on your Epson Projector, try the following: * Adjust the 'Brightness' and 'Brightness Control' settings in the configuration menu. * Adjust the 'Contrast' setting in the configuration menu. * If the lamp is nearing the end of its life, replace it with a new one.
T
Terrence TannerAug 28, 2025
How to fix fuzzy or out of focus images on my Epson EMP-822?
- B
  bowenAug 28, 2025
  To resolve fuzzy or out-of-focus images on your Epson Projector: * Adjust the focus by turning the focus ring. * Ensure the projector is set up within the recommended projection distance range. * Reduce the projection angle to lower the amount of keystone correction, as a large keystone adjustment can cause fuzziness.
C
Cheryl TorresAug 27, 2025
Why does my Epson EMP-822 show a High Temp Warning?
- P
  Patrick OconnellAug 27, 2025
  If your Epson Projector is showing a High Temp Warning, check that the air filter and air exhaust vent are not blocked, and make sure the projector isn't placed directly against a wall. If the air filter is clogged, clean or replace it.
C
Chad StephensAug 27, 2025
Why won't my Epson Projector power on?
- T
  Timothy WellsAug 27, 2025
  If your Epson Projector won't power on, try these steps: * Press the [Power] button to turn the power on. * Ensure the power cable is correctly connected and that the outlet is functioning. * Reinsert the power cable; if it still doesn't work, disconnect the projector and contact your local dealer. * If the operation lock is set to 'Full Lock', press and hold the [Enter] button on the control panel for about seven seconds to release the lock. * Check the 'Remote Receiver' setting in the configuration menu. * Press the [Power] button to turn the power back on.
M
Melissa BrownAug 25, 2025
How to fix the Epson EMP-822 Projector remote control when it's not working?
- J
  John SanchezAug 26, 2025
  If your Epson Projector's remote control isn't working, try these steps: * Point the remote control directly at the remote receiver on the projector. * Ensure you are within the remote control's operating range (about 6 m). * Make sure direct sunlight or strong light isn't shining on the remote receiver. * Check the 'Remote Receiver' setting in the configuration menu. * Verify the batteries are correctly inserted and replace them if necessary. * If a remote button has been pressed for more than 30 seconds, release it to resume normal operation.
B
Brian DavisAug 25, 2025
Why is there no audio from my Epson Projector, or the audio is too low?
- P
  Patricia JonesAug 25, 2025
  If you're experiencing low or no audio from your Epson Projector, consider the following: * Verify the audio source is correctly connected to the Audio port. * Adjust the volume to a suitable level. * Ensure A/V Mute is not active by pressing the [A/V Mute] button on the remote control. * Use an audio cable labelled 'No resistance'.

Epson EMP-822 Specifications

General

Resolution	1024 x 768 (XGA)
Contrast Ratio	400:1
Display Technology	3LCD
Projection Size	30 - 300 inches
Input Ports	S-Video
Noise Level	28 dB (eco)
Lamp Life	2000 hours (Normal mode), 3000 hours (Eco mode)
Power Consumption	280 W (Normal mode), 225 W (Eco mode)