EasyManuals Logo

Epson PowerLite S4 User Manual

Epson PowerLite S4
69 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #48 background imageLoading...
Page #48 background image
48
Problem Solving
Lamp or Temp indicator flashes orange
Fan related error/
Sensor error
Stop using the projector, disconnect the power cable from the electrical outlet, and contact Epson (see
page 57
).
High temperature error
(overheating)
The lamp will turn off automatically and projection will stop. Wait for about 5 minutes until the projector
switches to standby mode, then do the following:
Make sure the air filter and air exhaust vent are clear, and the projector is not positioned against a wall.
If the air filters are blocked, clean or replace them. See page 44
.
Press the [Power] button to turn the power back on. If this does not solve the problem and the projector
continues to overheat or the indicators continue to show a problem when the power is turned on, stop using
the projector, disconnect the power cable from the wall outlet, and contact Epson (see page 57
).
Lamp problem
Lamp timer failure
Lamp cover is open
Take out the lamp and check if it is broken. See page 41.
If the lamp is not broken, put it back in and then turn the power on. If the lamp still does not turn on, replace
it with a new lamp.
If this does not solve the problem, stop using the projector and disconnect the power cable from the
electrical outlet. Then contact Epson (see page 57
).
If the lamp is broken replace it with a new lamp, or contact Epson for further advice (see page 57). If
replacing the lamp yourself, be careful to avoid pieces of broken glass. (Projection cannot be carried out
until the lamp is replaced.)
Check that the lamp and the lamp cover are securely installed. If the lamp or lamp cover is not securely
installed, the lamp will not switch on.
When using above an altitude of about 1,500m, make sure you set the "High Altitude Mode" to
"On".
Status Cause Remedy or Status
Red
Red
Power
Red
Red
Power
Red
Red
Power
Lamp or Temp indicator flashes orange
Status Cause Remedy or Status
High temperature warning (This is not an abnormality, but if the temperature rises too high again, projection will stop automatically.)
Check that the air filter and air exhaust vent are clear and that they are not up against a surface such as a
wall.
If the air filter is clogged, clean or replace it. See page 44
.
Red
Orange
Power

Table of Contents

Other manuals for Epson PowerLite S4

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Epson PowerLite S4 and is the answer not in the manual?

Epson PowerLite S4 Specifications

General IconGeneral
Number of colors16.78 million colors
Projection distance6 m
Vertical scan range48 - 85 Hz
Horizontal scan range15 - 92 kHz
Projection technologyLCD
Contrast ratio (typical)500:1
Screen size compatibility30 - 300 \
Projector native resolutionSVGA (800x600)
Keystone correction, vertical-30 - 30 °
Lamp typeUHE
Lamp power170 W
Light source typeLamp
Service life of light source2000 h
Service life of light source (economic mode)3000 h
FocusManual
Focal length range16.6 mm
InterfaceUSB
Audio inputRCA x 2
Dimensions (WxDxH)246 x 328 x 100 mm
Power requirements100-240 V +/- 10%, 50/60 Hz AC
Connectivity technologyWired
Noise level36 dB
Dot clock scanning frequency162 MHz
RMS rated power1 W
Number of built-in speakers1
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Power consumption (standby)5 W
Power consumption (typical)250 W
Operating temperature (T-T)5 - 35 °C
Weight and Dimensions IconWeight and Dimensions
Weight2600 g

Related product manuals