Erbe VIO 200 D User Manual

152 pages

To Next Page

2018-1280113-341

USER MANUAL

VIO

200 D

V 2.3.x

ELECTROSURGERY

Default Chapter5
- Table of Contents5
1 Safety Instructions9
- Intended Use9
- Combination with Other Equipment9
- Safety Notations9
- Meaning of the Note9
- Who Must Read this User Manual10
- Compliance with Safety Information10
- Structure of Safety Instructions10
- Operating Errors and Incorrect Installation by Persons Without Training10
- Risks Due to the Environment11
- Electric Shock12
- Fire / Explosion13
- Burns14
- Inadvertent Tissue Damage18
- Risks Due to Incorrect Use of the Return Electrode19
- Defective Unit20
- Interference Caused by the Unit21
- Damage to the Unit and Accessories22
- Notes23
2 Safety Features25
- Nessy25
- How Do I Receive Information about the Safety Status of the Return Electrode26
- Automatic Monitoring of Equipment Output Error29
- Automatic Monitoring of the on Time30
- Protection from Operating Errors30
3 Accessories33
- Introduction33
- VIO 200 D Example Accessories34
- Check Compatibility of Instrument and CUT / COAG Mode with the Help of the Upmax Display36
- Check Compatibility of the Return Electrode38
- Compatible Footswitches38
4 Description of the Controls39
- Controls on the Front Panel39
- Controls on the Back41
5 Working with the Electrosurgical Unit: a Tutorial43
- The Tutorial and Your Electrosurgical System43
- Program43
- Adopt Program46
- Select Program46
- The Basic Concept of the Electrosurgical Unit: Focusing Attention on the Functions of a Receptacle (Focus View)48
- Changing Settings of the Basic Program48
- Setting Cut Mode49
- Setting CUT Effect50
- Selecting CUT Max. Wattage51
- Select COAG Mode, COAG Effect and COAG Power Limitation52
- Activation of CUT and COAG Modes with Footswitch52
- Activation of CUT and COAG Modes with Fingerswitch, AUTO START, AUTO STOP54
- The Focus View and Activation Concept of the Electrosurgical Unit. What Points Must I Observe56
- Nessy56
- How Do I Receive Information about the Safety Status of the Return Electrode57
- Saving the Amended Basic Program under a New Name61
- Overwriting a Program62
- Creating All Settings for a Program from Scratch63
- Deleting a Program63
- Creating Programs for Remode Function63
- Remode Change-Over with a 2-Button Handpiece67
- Calling up Setup68
6 Description of Receptacle Hardware71
- Purchasing Further Receptacles71
- Receptacles for Different Modes and Instrument Connectors71
- Monopolar Receptacle71
- Bipolar Receptacle72
- Receptacle for Return Electrode73
7 Monopolar Standard Modes75
- Auto Cut75
- Soft Coag77
- Swift Coag79
- Forced Coag81
8 Bipolar Standard Modes85
- Bipolar Cut85
- Bipolar Soft Coag87
- Bipolar Forced Coag89
9 Monopolar Optional Modes93
- Precise Cut93
- Dry Cut95
- Endo Cut Q97
- Endo Cut I98
- Precise Coag100
10 Bipolar Optional Modes103
- Bipolar Precise Cut103
- Bipolar Precise Coag105
11 APC Receptacle (Only Available with the APC Module)109
- APC Receptacle109
12 APC Standard Modes (Only Available with an APC Module)111
- Forced Apc111
- Precise Apc113
- Pulsed Apc114
- Argon-Assisted AUTO CUT Mode116
- Argon-Assisted SOFT COAG Mode118
- Argon-Assisted SWIFT COAG Mode120
- Argon-Assisted FORCED COAG Mode122
13 APC Optional Modes (Only Available with an APC Module)125
- Argon-Assisted DRY CUT Mode125
14 Installation129
- Ambient Conditions129
- Electrical Installation130
- Install Electrosurgical Unit on Overhead Support132
- Installing the Unit on an Erbe Equipment Cart133
15 Cleaning and Disinfection135
- Wipe Disinfection135
- Instructions for Cleaning and Disinfection135
- Safety Instructions135
16 Status Messages, Error Messages137
17 General Technical Data141
18 Information on Electromagnetic Compatibility (EMC)143
- Guidelines for Avoiding, Recognizing and Rectifying Unwanted Electromagnetic143
- VIO System143
19 Maintenance, Customer Service, Warranty, Disposal149
- Maintenance149
- Customer Service149
- Warranty150
- Disposal150
20 Symbols151

Other manuals for Erbe VIO 200 D

Service Manual144 pages

Quick Guide2 pages

Questions and Answers:

P
Paul LucasAug 2, 2025
Why are APC setup parameters invalid on my Erbe Medical Equipment?
- J
  Joshua TaylorAug 2, 2025
  If you encounter invalid APC setup parameters with your Erbe Medical Equipment, the solution is to analyze the CAN data, particularly looking for sector errors. Check the information provided with the equipment to assist with this analysis.
L
Loretta KaneAug 16, 2025
What to do if Erbe Medical Equipment shows a timeout of activation signal?
- G
  Gina WhiteAug 16, 2025
  If you are experiencing a timeout of the activation signal with your Erbe Medical Equipment, ensure uninterrupted CAN transmission by checking the shielded FS cable or the position of the FS cable relative to the HF cable. If the error persists, perform a CAN analysis using a tool like PCAN explorer.