Name: Esko Kongsberg XN IPC 2.0
Brand: Esko
Rating: 5 (1 reviews)

To Next Page

To Previous Page

Kongsberg XN / iPC 2.0

Empty vacuum cleaner in time

1. Do not leave the machine running if the

Vacuum Cleaner can be over-filled. This

might cause damage.

2. Be aware the risk of suction tube clogging.

12.8.5 Routing Advice

Milling bits

For thin materials, use bits with short cutting

length.

Default Chapter2
- Table of Contents2
1 Preface7
2 Change Record8
3 Welcome9
4 Using this Manual10
- Main Sections10
- Name Styles and Symbols11
- Pictures and Illustrations11
- Local Languages12
5 Safety Regulations13
- Introduction13
- Responsibilities13
- Requirements to be Met by Operators14
- Definition of Use14
- Danger Zones14
- Warning Sign Explanation17
- Safety Devices19
- Protective Equipment21
- Procedures in Case of Malfunctions21
- Residual Risk, XN21
6 System Description24
- Naming Conventions24
- Main Power Switch25
- Operators Panel26
- Variable Blow Back27
- Pressurized Air System28
- Application Programs Available29
7 Basic Operations30
- Power on Sequence30
- Reset Safety System31
- Power off Sequence31
- Continue after Safety Break31
8 Prepare for a Job33
- Introduction33
- Create Job33
- Layer Setup33
- Production Setup34
- Speed Setting34
- Flute/Grain Direction34
- Vacuum Zone Selection34
- Job Execution35
- Milling Production35
- Make a Pen Plot36
- Work with X-Pad36
9 How to Procedures, Advanced40
- Cutting Thick Materials40
- Hard Board Production40
- Multi Pass Milling41
- Jobs Including Reverse Operation41
- Work with Different Reference Point Settings42
- Multizone Production42
  - Multizone, Workflow44
10 System Setup46
- Introduction46
- Adjust X1 to X2 Angle47
- Register Table Size47
- Set Ruler Position48
- Set Main Reference Point48
- Map Table Top Surface49
- Reference Points and Coordinate System49
- Table Speed51
- Jog Settings52
- Table Acceleration52
- Set Table Top Reference53
- Vacuum Setup53
  - Vacuum Section Configuration53
  - Using Two Vacuum Pumps55
- Router Setup55
- Conveyor Belt Control55
  - Split Sheet Feed56
  - Sheet Feed Correction56
- Board Size56
11 Tool Configuration and Adjustment57
- Introduction57
- Adjust Active Tool57
- Tool Height Calibration58
- Lag Settings (for Rotating Tools)58
- Rotation Adjustment (for Rotating Tools)60
- Center Offset Adjustment61
- Manual Adjustment of Center Offset and Angle62
- Tool Offset62
- Maintain Tool List (more63
12 Tooling System65
- Tool Handling and Care65
- Tool Inserts with Built-In Motor65
- Tool Heads Available, Overview66
- Tool Head Mount / Dismount67
- Flexihead67
- Powerhead69
- Foamhead78
- Multicut-HP80
- Chiller 1 for Multicut-HP106
- Chiller2016 for Multicut-HP109
- Measuring Foot111
- Laser Pointer112
- X-Pad113
13 Tool Inserts115
- Ball Point Pen115
- Bevel Knife116
- Bevel Knife U20117
- Braille Tool117
- Corruspeed Knife122
  - Tool Adjustment123
- Crease Tool124
  - Tool Adjustment124
- Crease Tool, 60 MM125
  - Tool Adjustment125
- Drill Tools126
- Foam Knife128
- Ink Tool129
- Kisscut131
- Microcut133
- Psaligraphy Knife135
  - Tool Adjustment135
- RBI 90-16 (Rigid Board Insert)136
- Reciprocating Knife137
  - Tool Adjustment138
- Rigid Material Knife139
- Rotacut140
- Static Knife143
  - Tool Adjustment144
- VI45 Knife Tool144
14 Maintenance147
- Daily Maintenance147
- Weekly Maintenance147
- Maintenance, External Equipment147
15 Fuse Replacement148
- MPU Fuses148
- X1 Fuses149
- X2 Fuses149
- Y/Z Fuses150
- Tool Rotation/Reciprocating Knife Fuses151
- Chiller Fuse151
- Heater for Chiller Fuse153
- Chiller2016 Fuse Replacement153
16 Roll Feeder154
17 Collector Basket155
18 Vacuum Cleaner156
- Vacuum Cleaner, Zefiro156
  - How to Use156
- Vacuum Cleaner, High-Capacity, TB ESKO158
  - How to Use158
- Compact Vacuum Cleaner160
  - How to Use160
19 Install Software162
20 Frequently Asked Questions163
- Machine163
- Tools163
- Ipc164

Questions and Answers:

Need help?

Do you have a question about the Esko Kongsberg XN IPC 2.0 and is the answer not in the manual?

Esko Kongsberg XN IPC 2.0 Specifications

General

Brand	Esko
Model	Kongsberg XN IPC 2.0
Category	Cutter
Language	English

Related product manuals

Esko Kongsberg XP

218 pages

Esko Kongsberg C series

268 pages

Esko Kongsberg V-Series

144 pages

Esko Kongsberg XN IPC 2.0 User Manual

Table of Contents

Questions and Answers:

Esko Kongsberg XN IPC 2.0 Specifications

Related product manuals