How to fix a water leak in my Express Water Filtration System?
If you notice a water leak in your Express Water Filtration System, it may be due to tubing that isn't securely inserted or doesn't have a clean, smooth cut at the outer tip. Ensure the tubing is properly inserted. Also, check that the 3-way connector is correctly installed. Another possible cause is the feed water adapter, which may need re-installation.
Why is the purified water flow low in my Express Water Filtration System?
A low purified water flow in your Express Water Filtration System can be caused by a few things. First, ensure tap water is entering the system by checking that the cold water is fully turned on. Unscrew the feed adapter to check for any blockage inside the screen. Also, verify that the input tap water pressure meets the system's working pressure requirements. Another cause may be that the filter cartridge needs to be replaced. Contact EXPRESS WATER for assistance.
Why is the booster pump running loud on my Express Water Filtration System?
A loud booster pump in your Express Water Filtration System can stem from a couple of reasons. It might be due to low inlet pressure or low inlet water flow. Ensure the cold water is fully turned on to the system. Unscrew the feed adapter to inspect the screen for blockages. Also, check that the input tap water pressure meets the system's requirements. If the machine is being flushed during initial power-on, operation, or filter replacement, the sound is normal and will subside when flushing is complete.
What does it mean when the filter indicators blink red on my Express Water Filtration System?
If the working indicator and water quality indicator light are off and the filter indicators blink red on your Express Water Filtration System, it indicates an overtime protection issue. This happens when the system continually works for 30 minutes, triggering a buzzer alarm. If it continues for another 3 minutes, the system stops. To resolve this, power the system up again, and it should resume working.
Why is my Express Water Filtration System turning off and on?
If the working indicator and water quality indicator light are off and the filter indicators blink in violet on your Express Water Filtration System, it indicates frequent start and stop protection. This occurs when the system detects frequent starts and stops (high tension switch opening and closing in 60 seconds) for 20 continuous minutes, causing the system to beep five times before shutting down. To resolve this, power the system up again, and it should resume working.
Why is the temperature indicator blinking red on my Express Water Filtration System?
If the working indicator and ROM / ALK filter indicator light are off, and the SED+CAR filter indicator and water quality indicator blink in red on your Express Water Filtration System, it signifies low temperature protection. This occurs when the NTC detects inlet or outlet water temperature at or below 37°F, triggering five buzzer beeps. To resolve this, power the system up again, and it should resume working.
How to fix no display on my Express Water Filtration Systems?
If there is no display on your Express Water Filtration System, the power may not be connected. Check if there is electricity at the outlet by testing it with another electrical item.
Follow installation specs, ensure correct voltage, and use approved parts for safe operation.
Maintain proper temperature, avoid damage, and check components regularly.
Key warnings on water source, pressure, connections, and power adapter usage.
Cautions on placement, cleaning methods, and waste water pipe management.
Illustration and list of system parts, along with overall physical dimensions.
Details on model specifications, operational parameters, and water treatment process.
Verify installation area, tools, and completeness of parts before starting.
Guide for installing the feed water adapter valve to the cold water line.
Mandatory warnings regarding cold water line, pressure limits, and hot water avoidance.
Locate, mark, and drill the drain pipe for saddle installation.
Assemble and tighten the drain clamp halves with gasket for a secure fit.
Instructions for orienting and positioning the main system unit.
Detailed steps for inserting and locking filter cartridges into the system.
Cutting tubing, removing port plugs, and connecting inlet, waste, and pure water lines.
Instructions for drilling and securing the RO faucet to the counter or sink.
Visual guide of the fully assembled RO system and its connections.
Important checks for leaks and proper drain tubing connection after installation.
Detailed steps for initial system flush and water quality check.
Instructions for long-term storage and regular system upkeep.
How to properly twist off and install new filter cartridges.
Notes on using approved cartridges and factors affecting their lifespan.
Meaning of Working, Filter Life, and Water Quality indicator lights.
Location and function of buttons used to reset filter life indicators.
Explanation of automatic and manual flushing for various operational scenarios.
How indicator lights change during different flushing operations.
Understanding filter status based on indicator lights and buzzer alerts.
Steps to reset filter life indicators after cartridge replacement.
Resolving problems such as water leaks, no display, and loud pump noise.
Addressing issues like overtime, frequent start/stop, and low temperature protection.
What the 1-year warranty covers and its duration from purchase.
Procedure for claims, items not covered, and state-specific rights.
General| System Type | Reverse Osmosis |
|---|---|
| Filtration Stages | 6 |
| Operating Pressure | 40-80 PSI |
| Warranty | 1-year limited warranty |
| Capacity | 50 GPD (Gallons Per Day) |
| Operating Temperature | 40-100°F |
| Included Components | RO System, Filters, Faucet, Tank, Installation Kit |
To Next Page
