EasyManua.ls Logo

FAAC A140 AIR Series - User Manual

FAAC A140 AIR Series
70 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
A140 AIR
H100-H140
EN16005

Table of Contents

Questions and Answers

  • L
    lfreemanAug 13, 2025
    What to do if FAAC A140 AIR is not closing and the ERROR LED is off?
    • K
      Kendra MitchellAug 13, 2025
      If your FAAC Door Opening System is not closing and the ERROR LED is off, consider the following: * Ensure that the selected operating function is not DOOR OPEN (if no SD-Keeper is installed, make sure that input 8 of the J6 terminal board is not jumper connected to the negative). * Make sure that the selected operating function is not MANUAL. * Check the motor connection. * Check if power is being supplied to the motor (VMOT LED ON). * Also, check if the photocell/s are engaged.
  • T
    Teresa Scott DVMAug 16, 2025
    What to do if FAAC A140 AIR is not opening and the ERROR LED is off?
    • G
      Grant SteeleAug 16, 2025
      If your FAAC Door Opening System is not opening and the ERROR LED is off, try the following: * Ensure that the selected operating function is not MANUAL. * Make sure that the selected operating function is not NIGHT (if no SD-Keeper is installed, make sure that input 7 of the J6 terminal board is not jumper connected to the negative). * Check the motor connection. * Make sure that the motor lock is not locked. * Check if power is being supplied to the motor (VMOT LED ON).
  • J
    Jeffrey SmithAug 20, 2025
    Why is my FAAC Door Opening System SD-KEEPER off?
    • M
      Michael SalinasAug 20, 2025
      The FAAC Door Opening System SD-KEEPER might be off due to: * No mains power supplied and the control board is battery-powered in NIGHT operating function, and in energy saving statues. * Interrupted connection to the control board. * The control board not operating correctly. To resolve this: * Check the connection cables and wiring between the SD-Keeper and the control board. * If the control board is not operating correctly, replace it.
  • C
    Charles WilliamsAug 25, 2025
    What to do if my FAAC A140 AIR closes instead of opening, or opens instead of closing?
    • J
      Jennifer WilliamsAug 25, 2025
      If your FAAC Door Opening System closes instead of opening, or opens instead of closing, reverse the position of dip-switch 4 on the control board and execute a SETUP.
  • R
    Richard MercerAug 28, 2025
    Why are all LEDs off on my FAAC A140 AIR?
    • D
      Dennis ClarkAug 28, 2025
      If all the LEDs on your FAAC Door Opening System are off, it could be due to: * The 5x20 T2,5A fuse inside the power supply unit is interrupted. * Connector J1 is not fitted correctly on the control board. * The control board is not operating correctly. To solve this, check the connection to the power supply unit and replace the control board if necessary.
  • C
    Charles NealSep 1, 2025
    Why is the FAAC A140 AIR POWER led OFF but 24V= led ON?
    • S
      smithtimothySep 1, 2025
      The FAAC Door Opening System POWER led might be OFF while the 24V= led is ON because mains power is not supplied and the control board is battery-powered. See point B for further instructions.
  • K
    Kevin SimpsonSep 4, 2025
    What to do if FAAC Door Opening System is moving for short distances only?
    • U
      urodriguezSep 4, 2025
      If the FAAC Door Opening System is moving for short distances only, check if encoder connector J17 is correctly inserted, check the condition of the encoder and check the condition of the encoder connection flat cable.
  • P
    palmerangelaSep 8, 2025
    Why are the FAAC A140 AIR door movements very slow?
    • C
      Christopher BarnesSep 8, 2025
      If the FAAC Door Opening System door movements are very slow, using the SD-Keeper+Display, check if the selected speed levels are as required and check if the selected deceleration distances are as required.

Summary

EC Declaration of Incorporation

Automatic Door A140 AIR H100 - H140

Product Description and Components

Describes the automatic operation, assembly, and components of the door system.

Included Accessories

Lists and describes accessories that are pre-assembled on the cross beam.

Door Frame Accessories

Electrical Preparations

Details how to route electrical cables for accessories and power supply connections.

Technical Specifications

Provides technical data, dimensions, and performance metrics for the A140 AIR models.

Assembly of In-Kit Automated Systems

Preparing the Support Profile

Describes how to prepare and cut the support profile for installation.

Support Profile Securing on Wall

Details the process of fixing the support profile to a wall or structure.

Preparing the Leaves

Installing the Lower Sliding Blocks

Adjusting the Leaves

Instructions for installing and adjusting the door leaves on the carriages.

Adjusting the Opening Mechanical Stops

Fitting the Electronics Module and Motor Unit

Start-Up of the Automated System

Fitting the Motor Lock

Adjusting the Motor Lock

Procedure for adjusting the motor lock for proper leaf locking.

Installation of Assembled Automated System

Securing the On-Wall Support Profile

Refers to Chapter A for details on securing the support profile to a wall.

Free-Standing Kit Installation

Free-standing profile - wall-mounted

Instructions for wall-mounting the free-standing profile.

Free-standing profile - fastening with side brackets

How to secure the free-standing profile using side brackets.

E100 - E140 Control Board

Connection Terminal J7

I-DET Input

Description of the Internal sensor input (I-DET) and its configuration.

E-DET Input

Description of the External sensor input (E-DET) and its configuration.

EMERG1 Input

Description of the Emergency command 1 input and its operation.

EMERG2 Input

Description of the Emergency command 2 input and its operation.

PROTECTION 1 Input

Description of the Protection 1 input for safety devices.

PROTECTION 2 Input

Description of the Protection 2 input for safety devices.

-FAIL-SAFE Input

Description of the -FAIL-SAFE input for monitoring sensors.

OUT 1 Output

Description of the output (OUT 1) function, e.g., for alarms.

+24 V= Power Output

Description of the +24V= output for powering accessories.

Connection Terminal J4

Button Photocell Connections

Diagrams and instructions for connecting button photocells to terminal J4.

DIP-Switch Programming

Start-Up Procedure

Describes the automatic setup procedure executed upon first power-up.

Standard Configuration

Details the default configuration settings for the automatic door system.

Terminal-board J6

SD-KEEPER Usage

Instructions for connecting and using the SD-Keeper programming unit.

Description and Use of Energy Saving

Function Description

Explains the Energy Saving mode, its benefits, and how it works.

Energy Saving Function Activation Mode

How to activate the Energy Saving function via the control board or SD-Keeper.

Programming the E100-E140 Board

Closing Speed Setting

Sets the speed level for door closing.

Opening Speed Setting

Sets the speed level for door opening.

Protection 1 Configuration

Configures the Protection 1 input status and safety device behavior.

Protection 2 Configuration

Configures the Protection 2 input status and safety device behavior.

Programming the E100 - E140 Board rev.4.5

Battery Kit Configuration

Enables and configures the battery kit functions.

Motor Lock Kit Configuration

Enables and configures the motor lock functions based on operating modes.

SD-Keeper Programming Unit

Fitting the SD-Keeper

Provides an exploded view and instructions for fitting the SD-Keeper.

SD-Keeper Diagnostics

Explains the diagnostic function of the SD-Keeper for identifying alarms.

Special Functions

Setup Procedure

Describes the door initialization process where parameters are self-learned.

Reset Function

Function to restore normal operating conditions after alarms.

Lock;Unlock SD-Keeper

Activates or deactivates the SD-Keeper lock function.

Programming Flowchart

Partial Opening Configuration

Sets the percentage for partial opening in the automatic function.

Obstacle Detection Configuration

Configures standard or no-standard obstacle detection behavior.

Programming Flowchart

EMERG1 Input Configuration

Configures the behavior of the EMERGENCY 1 input.

EMERG2 Input Configuration

Configures the behavior of the EMERGENCY 2 input.

Photocell Configuration

Sets the quantity and fail-safe status of photocells.

Advanced Menu Flowchart

Operation Parameters

Adjusts fundamental operational parameters like speeds and widths.

Input;Output Setup

Configures input and output functions of the control board.

Change Password

Allows changing the password for advanced menu access.

Advanced Menu Flowchart

Stand Setup

Checks for and resets non-standard programming.

Interlock Configuration

Configures the interlock function for controlling two sliding doors.

Setup

Partial Opening Setting

Selects opening percentage for partial opening function.

Pause Time Setting

Enables or disables pause time in automatic mode.

Obstacle Detection Setting

Sets obstacle detection behavior for opening and closing.

Battery Settings

Battery Kit Enable;Disable

Enables or disables the battery kit.

Battery Operation Behavior

Defines battery operation behavior during power cuts.

Motor Lock Configuration

Motor Lock Kit Settings

Configures the motor lock's operation based on different modes.

Motor Lock Operation Modes

Night Lock Setting

Manages motor lock behavior in night mode with discharged batteries.

Motor Lock Surveillance

Enables or disables the motor lock surveillance device.

Diagnostics

SDM L Software Version

Displays the control board software version.

Alarm Information

Lists current alarms, their numbers, and descriptions.

Advanced Menu Flowchart

Operation Parameters Adjustment

Adjusts fundamental operational parameters like speeds and widths.

Input;Output Setup

Configures input and output functions of the control board.

Change Password

Allows changing the password for advanced menu access.

Miscellaneous Settings

Stand Setup Check

Checks for and resets non-standard programming.

Interlock Configuration

Configures the interlock function for controlling two sliding doors.

Interlock Function

Interlock with Internal Sensors

Describes interlock configuration using internal sensors.

Interlock with Push-Buttons

Describes interlock configuration using push-buttons.

Accessories

Motor Lock Installation

Installation procedure and configuration for the motor lock.

Battery Kit Installation

Instructions for connecting and installing the battery kit.

Motor Lock Supervision

How to activate motor lock surveillance for error detection.

Special Functions

Setup Initialization

Initializes parameters and learns door behavior.

Reset Operation

Restores normal operation after alarms.

Lock;Unlock SD-Keeper

Activates or deactivates the SD-Keeper lock function.

Sede Headquarters

Technical Assistance in Italy

Contact details for technical assistance within Italy.

Worldwide Subsidiaries

Contact information for FAAC subsidiaries worldwide.

FAAC A140 AIR Series Specifications

General IconGeneral
BrandFAAC
ModelA140 AIR Series
CategoryDoor Opening System
LanguageEnglish

Related product manuals