Need help?Do you have a question about the FAAC A1000 and is the answer not in the manual?
General| Brand | FAAC |
|---|---|
| Model | A1000 |
| Category | Door Opening System |
| Language | English |
Critical safety advice for installers, users, and workplace safety.
Explanation of symbols for warnings, references, and tools used in the manual.
Specifies the designed purpose and compliance standards for the A1000 system.
Lists forbidden applications and misuse of the automation system.
Information on the location and content of the product's identification plate.
Detailed technical data including dimensions, power, and operating parameters.
Describes the different supply configurations available for the A1000 automation.
Checks for structural soundness, level flooring, and absence of hazards.
Guidelines for safe and compliant electrical cable layout and protection.
Instructions for safe handling of packaged automation components.
Steps for unpacking and safely handling the automation components.
Detailed guide on assembling mechanical stops and other components.
Instructions for installing the electronic module onto the support profile.
Guidelines for installing safety cables and vibration damper spacers.
Steps for mounting the motor onto the support profile.
Instructions for installing the return pulley.
Details on installing and testing the motor release monitor and XB LOCK motor block.
Procedures for cover drilling, installing monitor sensors, and emergency battery.
Detailed instructions for frame assembly using TK50 profiles.
Steps to prepare for head section installation, including component removal.
Detailed guide on how to securely mount the head section to the wall.
Instructions for mounting different types of lower shoes for leaf installation.
Steps for attaching profiles to the leaves, including lower guide profiles.
Instructions for installing the optional lower sweeper accessory.
Procedures for disassembling carriages and installing leaves onto the profile.
Guide on adjusting leaf height, depth, and counter wheels for proper operation.
Steps for mounting brushes for both double and single leaf automations.
Procedures for properly adjusting the belt tension for smooth operation.
Detailed steps and table for accurate belt tensioning measurements.
Instructions for adjusting mechanical stops for correct opening and closing limits.
Steps for mounting side profiles to ensure the casing remains closed.
Guide for installing casing brackets, especially when side profiles are not used.
Instructions for securely fitting the automation system's cover.
Steps for installing the XB LOCK motor block onto the motor body.
Guide on how to adjust the XB LOCK motor block for proper clearance.
Instructions for installing cable guides to prevent interference with moving parts.
Detailed steps for installing the E1SL electronic board and power supply unit.
Explanation of the status LEDs on the E1SL electronic board.
Detailed description of terminal boards and connectors on the E1SL board.
Description of various connectors (J1-J25) on the E1SL board for inputs, outputs, and modules.
Steps for connecting motor, encoder, and XB LOCK motor block to E1SL.
Installing and configuring XV1/XDT1 detectors for opening and safety.
Configuration for using two XDT1 detectors for opening and safety.
Instructions for installing XBFA detectors for safety in opening movements.
Configuring photocells, inputs (E1/E2), and outputs (J22).
Step-by-step guide for powering on and performing the initial system setup.
Instructions for performing basic and advanced programming of the automation system.
How to select and set different operating modes for the automation.
Detailed configuration of system inputs for safety devices and activation.
Options for configuring the J22 outputs for various functions.
Settings for obstacle detection during opening and closing operations.
Details on anti-intrusion and Pull&Go features for enhanced security.
How to activate and configure the energy-saving function for efficiency.
Settings for the Low Energy function to limit leaf kinetic energy and forces.
How to interpret system status, alerts, and error indicators.
List of error codes, their meanings, and required intervention steps.
Explanation of warning codes and status indications for system operation.
List of auxiliary errors and their corresponding required actions.
A guide to resolving common issues not covered by system diagnostics.
Step-by-step guide to perform the system setup procedure.
How to perform a board reset to its initial state.
Procedure to reset all board parameters to factory default settings.
Instructions for updating the board's firmware and configuration via USB.
How to download board files, configuration, and log data to a USB device.
Setting up the Master/Slave configuration for Intermode operation.
Configuring the Interlock function for synchronized door operation.
Steps for assembling and testing the LK EVO device.
How to navigate and select operating modes using the LK EVO selection buttons.
Using key combinations for special functions like Lock/Unlock, Reset, and Firmware Version.
Procedures for assembling and testing the KS EVO unit.
How to navigate and select functions using the KS EVO key.
Steps for assembling and testing the SDK EVO device.
Guide on powering on the SDK EVO and navigating its interface.
Understanding the Home Page layout and button functions on the SDK EVO.
Procedures for resetting the board or locking/releasing the SDK EVO.
How to enter and manage passwords for accessing SDK EVO functions.
Navigating the operating mode selection menu on the SDK EVO.
Accessing and navigating the various function menus on the SDK EVO.
Detailed structure of the programming menu, including sub-menus and parameters.
Setting the language and accessing the main programming menu for inputs/outputs.
Configuring outputs (O1/O2) and safety inputs (S1/S2, E1/E2) for system functions.
Adjusting movement parameters, motor block, timing, energy saving, and battery kit.
Configuring installation, intercom network, and miscellaneous system settings.
Configuring partial opening, board display, intrusion detection, and SDK EVO key functions.
Method for estimating performed cycles to track maintenance intervals.
Regular checks to ensure the proper functioning and safety of the automation.
Schedule for mandatory and recommended replacement of worn components.
Safety precautions and requirements for maintenance personnel.
Detailed steps for replacing key components like belts, motors, and carriages.
Procedures for replacing the emergency battery and electronic board.
Instructions for safely replacing fuses in the system.
Diagrams showing the placement of components on the support profile.
Visual guide for installing the A1000 with two TK20 sliding and two fixed side leaves.
Visual guide for installing the A1000 with one TK20 sliding and one fixed side leaf.
Visual guide for installing the A1000 with one TK20 sliding leaf.
Shows component positions for a right-opening single-leaf configuration.
Detailed diagram and table for component placement in a left-opening single leaf.
Detailed diagram and table for component placement in a double-leaf configuration.
Essential safety advice for operating and maintaining the A1000 automation.
Instructions for manually opening/closing the door and using the release mechanism.
How to navigate and select operating modes using the SDK EVO.
Procedures for entering and managing passwords on the SDK EVO.
How to navigate and select operating modes using the LK EVO.
To Next Page
