What to do if my FBD 773 Beverage Dispenser displays 'Board Failure'?
If your FBD Beverage Dispenser is showing a 'Board Failure', cycle the power to the unit to see if it will clear the error. If not, replace the control board, because the control board may not be functioning properly.
How to diagnose 'Motor Failure' in FBD 773 Beverage Dispenser?
To resolve a 'Motor Failure' on your FBD Beverage Dispenser, run a beater circuit diagnostic to determine the problem or refer to error #58X in this manual. Check to make sure the beater motor is plugged in, because the beater motor may not be operating.
Why does my FBD 773 Beverage Dispenser say 'Compressor Ran Too Long'?
If your FBD Beverage Dispenser shows 'Compressor Ran Too Long', and the location is an extreme volume venue such as a festival, contact FBD service for instructions on adjusting the timer. Otherwise, run the refrigeration diagnostic sequence to determine the reason for the failure, because the compressor may have run continuously for more than 90 minutes.
What to do if my FBD Beverage Dispenser displays Error #111, 112, 113, 114: Motor Failure?
If your FBD Beverage Dispenser displays Error #111, 112, 113, 114 indicating 'Motor Failure', it means the beater motor is not operating. To solve this: * Run a beater circuit diagnostic to determine the problem or refer to error #58X in this manual. * Check to make sure the beater motor is plugged in.
What does error #200: Return Temperature Sensor mean on my FBD Beverage Dispenser and how do I fix it?
Error #200 'Return Temperature Sensor' on your FBD Beverage Dispenser indicates that the refrigeration return (suction) temperature sensor is not reading correctly. To fix it: * Ensure the temperature sensor is plugged in. * Replace the sensor if faulty.
Why does my FBD Beverage Dispenser say 'CO2 OUT'?
The FBD Beverage Dispenser displays 'CO2 OUT' when the CO2 supply is depleted. Restore the CO2 supply to resolve this. The dispenser will automatically restart.
What to do for 'High regulated CO2 PSI' on FBD 773?
If your FBD Beverage Dispenser displays a 'High regulated CO2 PSI' error, check the “carbonation” regulator on the header tray and ensure it is set to 60 PSI, because regulated CO2 pressure may be above 70 PSI.
How to fix 'Low regulated CO2 PSI' on FBD Beverage Dispenser?
If you encounter a 'Low regulated CO2 PSI' error on your FBD Beverage Dispenser, make sure the CO2 supply is not low. Check the “carbonation” regulator on the header tray and ensure it is set to 60 PSI, because the regulated CO2 pressure may have dropped below 50 PSI.
How to resolve 'High Barrel Pressure' on FBD 773?
To troubleshoot a 'High Barrel Pressure' error on your FBD Beverage Dispenser, dispense a drink to reduce the barrel pressure. If set to the ON mode, the unit will refreeze. Run the fill diagnostic if a failed component is suspected. Check the “Active Charge” regulator located on the product header to ensure it is set at 30 PSI. Make sure all barrels should be fully depressurized before checking the active charge, because pressure on a barrel may have exceeded 55 PSI.
What to do if my FBD 773 says 'Water Out'?
To fix a 'Water Out' error on your FBD Beverage Dispenser, make sure the water line to the unit is on and the water shutoff at the solution module is turned on. Ensure the CO2 supply line is connected to the water pump and that the pump is not stalled. Verify the CO2 supply pressure at the dispenser is reading 70 PSI, adjusting the regulator if needed. Also, check that the water pressure transducer is connected and working properly, because water pressure may be less than 45 PSI.
Essential for safe operation, grounding required.
Safety precautions for gas leaks and cylinder handling.
Handling heavy equipment and lifting safety.
Guidelines for placing the dispenser for optimal performance and ventilation.
Instructions for connecting the dispenser to the power supply.
Details water, syrup, and gas connections at the dispenser's rear.
Procedures for connecting the water line, including backflow prevention.
Guidelines for connecting gas supply from tanks or bulk systems.
Instructions for running syrup lines and ensuring proper pressure.
Steps to check for leaks and prime the system with product.
Guide for powering on the dispenser and verifying initial settings.
Procedure for adjusting water flow and setting brix for optimal taste.
Steps to purge air, fill barrels, and initiate the freezing process.
How to initiate the freezing cycle for product.
Explains the importance and process of defrosting for quality.
Factors affecting drink quality and adjustment settings.
Accessing and interpreting error logs.
Accessing technician-specific functions.
Options for barrel purging, filling, draining, and calibration.
Configuring dispenser settings like serial number, units, and display options.
Setting up primary and secondary gas types.
Configuring drink types based on gas selection.
Adjusting the amount of gas in the drink.
Adjusting the drink's frozen consistency.
Detailed setup for primary and secondary gas types.
Running system diagnostics to identify malfunctions.
Interpreting common messages displayed on the home screen.
List and explanations of error codes and their solutions.
Troubleshooting for safety fill errors.
Troubleshooting for beater motor low errors.
Troubleshooting for compressor running excessively long.
Troubleshooting for high barrel pressure conditions.
Troubleshooting for hot product detection shutdown.
Troubleshooting for beater motor failure.
Troubleshooting fan startup issues.
Troubleshooting compressor startup issues.
General| Brand | FBD |
|---|---|
| Model | 773 |
| Category | Beverage Dispenser |
| Language | English |
To Next Page
