FBD 773 - User Manual

Other manuals for FBD 773

Installation And Operation Manual42 pages

Questions and Answers

V
Vernon HicksAug 26, 2025
How to resolve 'High Barrel Pressure' on FBD 773?
- M
  mackmitchellAug 26, 2025
  To troubleshoot a 'High Barrel Pressure' error on your FBD Beverage Dispenser, dispense a drink to reduce the barrel pressure. If set to the ON mode, the unit will refreeze. Run the fill diagnostic if a failed component is suspected. Check the “Active Charge” regulator located on the product header to ensure it is set at 30 PSI. Make sure all barrels should be fully depressurized before checking the active charge, because pressure on a barrel may have exceeded 55 PSI.
E
erica37Aug 26, 2025
How to fix 'Low regulated CO2 PSI' on FBD Beverage Dispenser?
- J
  John KennedyAug 26, 2025
  If you encounter a 'Low regulated CO2 PSI' error on your FBD Beverage Dispenser, make sure the CO2 supply is not low. Check the “carbonation” regulator on the header tray and ensure it is set to 60 PSI, because the regulated CO2 pressure may have dropped below 50 PSI.
R
riveraleahAug 27, 2025
What to do for 'High regulated CO2 PSI' on FBD 773?
- N
  Nicole MeadowsAug 27, 2025
  If your FBD Beverage Dispenser displays a 'High regulated CO2 PSI' error, check the “carbonation” regulator on the header tray and ensure it is set to 60 PSI, because regulated CO2 pressure may be above 70 PSI.
A
Andrea KnappAug 27, 2025
What does 'Hot Product Detected' mean on my FBD 773?
- W
  williamstephensAug 27, 2025
  If your FBD Beverage Dispenser is displaying 'Hot Product Detected', check the return temperature sensor for proper operation. If hot product was detected, call FBD for technical assistance, because product in a barrel may exceed 85°F.
J
Jonathan WatkinsAug 27, 2025
What to do if FBD 773 shows 'Safety Fill Error'?
- A
  antonioowensAug 28, 2025
  To address a 'Safety Fill Error' on your FBD Beverage Dispenser, run the fill diagnostic sequence to determine the reason for the failure, because a barrel may have filled continuously for more than two minutes.
A
alexandra71Aug 28, 2025
How to troubleshoot 'Beater Low Error' on FBD 773 Beverage Dispenser?
- J
  James JohnsonAug 28, 2025
  To address a 'Beater Low Error' on your FBD Beverage Dispenser: 1. Check the brix in the barrel. If low, check the brix at the sample valve and adjust if needed. 2. Drain and refill the barrel. 3. Check the fault code history for multiple sold out errors within a short period. This can mean that the BIB connector or syrup pump has a suction leak. Fix if necessary. 4. Run the beater circuit diagnostic if a component failure is suspected, because the beater motor may have stalled during operation.
K
Kristin DiazAug 29, 2025
Why does my FBD 773 Beverage Dispenser say 'Compressor Ran Too Long'?
- S
  Sarah ShortAug 29, 2025
  If your FBD Beverage Dispenser shows 'Compressor Ran Too Long', and the location is an extreme volume venue such as a festival, contact FBD service for instructions on adjusting the timer. Otherwise, run the refrigeration diagnostic sequence to determine the reason for the failure, because the compressor may have run continuously for more than 90 minutes.
W
westbrendaAug 29, 2025
How to diagnose 'Motor Failure' in FBD 773 Beverage Dispenser?
- R
  richard54Aug 29, 2025
  To resolve a 'Motor Failure' on your FBD Beverage Dispenser, run a beater circuit diagnostic to determine the problem or refer to error #58X in this manual. Check to make sure the beater motor is plugged in, because the beater motor may not be operating.
L
lindaadamsAug 30, 2025
What to do if my FBD 773 Beverage Dispenser displays 'Board Failure'?
- R
  richard67Aug 30, 2025
  If your FBD Beverage Dispenser is showing a 'Board Failure', cycle the power to the unit to see if it will clear the error. If not, replace the control board, because the control board may not be functioning properly.
S
Samantha SandovalAug 30, 2025
How to fix 'Temperature Sensor Failure' on FBD 773 Beverage Dispenser?
- M
  Megan RogersAug 30, 2025
  To troubleshoot a 'Temperature Sensor Failure' on your FBD Beverage Dispenser, check the sensor and replace it if necessary, because the temperature sensor reading may be out of range.